CD-3440 Portable Compact Disk Player (420-5051) Operation Faxback Doc. # 18441 PLAYING A CD Your CD player can play standard 5- or 3-inch CDs that have this mark on them: COMPACT/disk/DIGITAL AUDIO Follow these steps to play a CD. 1. Set VOLUME to the minimum level. Be sure HOLD on the left side of the CD player is set to OFF. 2. Lift up OPEN to open the disc compartment cover. 3. Carefully place the CD, label side up, over the disc compartment's center hub. Press down slightly on the CD until it clicks and lies flat in the compartment, then close the cover. The display briefly shows a flashing -- then the total number of tracks on the CD. After several seconds the CD player turns off. 4. Press >II. The CD player turns on and shows the total number of tracks on the CD. Then track 1 begins to play. As the tracks play, the display shows the current track number. 5. Adjust the volume to a comfortable listening level, using either of the following guidelines: If you connected earphones, amplified speakers, or a CD-to-cassette adapter to the CD player's PHONES jack, set the CD player's VOLUME to the desired level. NOTE: The CD player's VOLUME control affects only the volume level you hear through the PHONES jack, not the volume level of the sound you hear through the LINE OUT jack. If you connected the player's LINE OUT jack to your home audio system or your car's stereo, use the volume controls on those units to set the desired volume as needed. CAUTION: To avoid speaker damage, set your audio system or car stereo's volume control to the minimum level before you play a CD. After the CD player begins to play, slowly increase the volume. 6. When the last track finishes playing, the CD player automatically stops and turns off. To stop PLAYING the CD before it ends, press STOP. The display shows 00 for about 10 seconds, then the CD player automatically turns off. LOCKING THE CONTROLS To prevent accidentally turning the CD player on or off, or changing the track you are listening to, set HOLD to ON. No controls work. Set HOLD to OFF to operate the controls again. AUTOMATIC SEARCH MUSIC SYSTEM You can use the automatic SEARCH music system (ASMS) during normal or programmed play to quickly locate any track on a CD. During play, press I<< to return to the beginning of the current track. Press I<< again to return to the beginning of the previous track. To move to the beginning of the next track, press >>I. You can also use the ASMS feature before you begin normal play. Repeatedly press >>I or I<< to select the track you want to play. Then press >II within about 10 seconds to play the track. AUDIBLE SEARCH Use audible search during play to rapidly search forward or backward to locate a specific section of a track. During audible search, the CD plays at a lower volume and a higher speed. To search forward, press and hold >>I. To search backward, press and hold I<<. Release the button to resume normal play. NOTES: If you press and hold down >>I while the last track plays, the CD player automatically stops and turns off at the end of the track. If you press and hold down I<< while the first track plays, normal play automatically starts from the beginning of the first track. PAUSE AND CUE To temporarily pause play, press >>II. The track number flashes on the display. Press >II again to resume play. NOTE: If you pause a CD for over 3 minutes, the CD player turns off. You can also use >>II to cue a track. When the CD player is stopped, press >>I or I<< to select the track you want to cue. Then press >>II twice. The track number flashes on the display. To cue a track in a programmed sequence (see "Programming the CD-3440"), (below) repeatedly press P MODE until M (without LEFT CIRCULAR ARROW) appears on the display. Then press >II twice when the CD player is stopped. The track number flashes on the display. Press >>I or I<< to display the track you want to cue. To play the cued track, press >>II. REPEAT PLAY Your CD player can repeat a single track, the entire CD, or a programmed sequence (see "Programming the CD-3440"). (below) To repeat a single track, repeatedly press P MODE until 1 and LEFT CIRCULAR ARROW appear on the display. At the end of the track, the CD player repeats it. To repeat an entire CD, repeatedly press P MODE until ALL and LEFT CIRCULAR ARROW appear on the display. When the CD player reaches the end of the CD, it returns to the first rack and replays all the tracks. To repeat a programmed sequence, repeatedly press P MODE during play until LEFT CIRCULAR ARROW appears and M and the first programmed number flash on the display. Press >II. M and a track number light steadily, and the programmed sequence repeatedly plays. To cancel repeat play, press STOP or repeatedly press P MODE until LEFT CIRCULAR ARROW disappears from the display. SPECIAL FEATURES PROGRAMMING THE CD-3440 Programming and playing a sequence of Tracks You can program up to 16 tracks on a CD to play in any order you choose, and even program the same track to play more than once. 1. During play, repeatedly press P MODE until M (without LEFT CIRCULAR ARROW and the track number 00 flash on the display. 2. Press either >>I or I<< to display the number of the first track you want to program. 3. Press M-SET to store the selected track number. The selection number advances by one, and the track number on the display changes to 00. 4. Repeat Steps 2 and 3 for each track you want to program, up to 16 tracks. NOTE: The CD player automatically begins to play if you program 16 tracks. 5. To play the programmed sequence, press >II. M lights steadily and the first track in the sequence plays. After the last programmed track ends, the CD player stops. At the end of programmed play, M disappears from the display, but the programmed sequence stays in the CD player's memory. NOTES: While you play the programmed sequence, you can use >>I to move forward or I<< to move backward in the sequence. To return to normal play from programmed play, repeatedly press P MODE until M disappears from the display. To restore programmed play after it has stopped, press P MODE repeatedly until M (without LEFT CIRCULAR ARROW) appears on the display. Then press >>II within 8 seconds to play the programmed tracks. Checking, Adding to, Replacing, or Clearing a Track in the Programmed Sequence To check the programmed sequence, repeatedly press P MODE until the first programmed track number and M (without LEFT CIRCULAR ARROW) flash on the display. Then repeatedly press M-SET. Each time you press M-SET, the player displays the number of the next track in the sequence. To add to the end of a programmed sequence, repeatedly press P MODE until the first programmed track number and M (without LEFT CIRCULAR ARROW) flash on the display. Then repeatedly press M-SET until 00 flashes on the display. Press >>I or I<< to display the new track number you want to program. Then press M-SET. NOTE: You cannot program more than 16 tracks. To replace a programmed track, repeatedly press P MODE until the first programmed track number and M (without LEFT CIRCULAR ARROW) flash on the display. Then repeatedly press M-SET to view the track numbers in the programmed sequence. When a track number you want to replace flashes on the display, press >>I or I<< to select the track you want to program in its place. Then press M-SET to program the new track number. To clear the programmed sequence from memory, press STOP to stop the CD player, then lift up OPEN to open the disc compartment cover. (JC 11/9/95)