3820 HD  
(250-3572)           Using the SETUP382 Utility       Faxback Doc. # 1783

The setup program is found on MS-DOS diskette # 2.

┌─────────────────────┬─────────────────────────┬─────────────────────────┐
│     Date & Time     │         Start up        │      Communications     │
├─────────────────────┼─────────────────────────┼─────────────────────────┤
│                     │                         │ Serial Ports [Enabled ] │
│  Date [03/31/1992]  │  Num Lock Light  [ON ]  │    Addresses  [Normal ] │
│  Time [14:31:19]    │  CPU Speed      [Fast]  │ Parallel Port [Printer] │
│                     │  Shadow RAM      [NO ]  │  Bidirection      [YES] │
├─────────────────────┼─────────────────────────┼─────────────────────────┤
│    Video/Speaker    │          Power          │          Timeouts       │
├─────────────────────┼─────────────────────────┼─────────────────────────┤
│Mode           [VGA] │  Management     [ON ]   │Suspend Mode [00] Minutes│
│Monitor  [LCD COLOR] │  Resume Mode    [OFF]   │Standby Mode [08] Minutes│
│Cursor Type    [Line]│  VRAM Timeout [Enabled ]│Display      [04] Minutes│
│Speaker        [ON ] │                         │Hard Drive   [01] Minutes│
├─────────────────────┴─────────────────────────┴─────────────────────────┤
│<ESC> Exit to DOS without saving setup   <CTRL-BRK> Reboot without saving│
│<F1>  Help for option that cursor is on     <SPACE> Toggles options      │
│<F2>  Save setup and exit                   <ARROW> Moves to next option │
└─────────────────────────────────────────────────────────────────────────┘

Using the SETUP382 Utility:

The Setup program (Setup382) lets you change startup parameters,
power-management parameters, and other system parameters that you use in
MS-DOS. Use the commands at the bottom of the screen to easily select and
change the parameters.

To run the Setup program, follow these steps:

1. Exit from any program you are currently in.
2. If you are not in Drive C, type:  c: <ENTER>
3. Select the DOS directory by typing: cd \dos <ENTER>
4. At the MS-DOS prompt, type: Setup382 <ENTER>
   The Setup program screen appears.
5. Use the up and down arrows to select the parameter you want, and press
   the spacebar to choose the setting.
6. Press F2 if you want to save your changes. If you do not want to save 
   the changes, press ESC.

The SETUP382 Utility lets you select system and power parameters, and store
the parameters you select in memory.  The computer uses these parameters 
each time you start it up.  Whenever you use the SETUP program, you must 
restart the computer to initialize the new parameters.

The SETUP382 parameters are arranged in the following groups:

* DATE AND TIME--These parameters allow you to set the DOS date and time.
* STARTUP--These parameters allow you to choose some of the internal 
  settings that activate when you turn on your computer. You can use this 
  group of parameters to select the initial program to run, the computer's 
  speed (fast or slow), and the Shadow RAM.
* COMMUNICATIONS--These parameters allow you to turn the serial ports on 
  and off, and to set the parallel port to operate with an external printer
  or diskette drive.
* VIDEO/SPEAKER--These parameters allow you to select the type of video
  monitor emulation and the type of cursor you want to use with your 
  computer.  You can also turn the computer's speaker on and off.
* POWER--These parameters allow you to turn some of the computer's power
  saving options on and off, such as the computer's low-power management
  parameter, the floppy disk standby parameter, and the Resume mode. You 
  can also turn on and off the VRAM Timeout feature.
* TIMEOUTS--These parameters allow you to save additional battery power by
  instructing the computer to automatically turn the display or hard drive 
  if you are not using the computer for a specified period of time.

(/tmc-12/02/95)