Packard Bell (250-0304) Pinouts Faxback Doc. # 3753 Statesman 200C Serial Connectors One external 9-pin sub-D connector and one internal 16-pin dual row header with power distribution for the modem. PIN SIGNAL PIN SIGNAL 1 Carrier Detect 6 Data Set Ready 2 Receive Data 7 Request to Send 3 Transmit Data 8 Clear to Send 4 Data Terminal Ready 9 Ring Detect 5 Signal Ground Case Ground Parallel Port One Parallel port is provided using the 25-pin sub-D connector. PIN SIGNAL PIN SIGNAL 1 Strobe 14 Automatic Feed 2-9 Databits 0-7 15 Printer Error 10 Acknowledge 16 Initialize 11 Printer Busy 17 Select Input 12 Paper Out 18-25 Ground 13 Select PCMCIA Interface PIN SIGNAL PIN SIGNAL 1 Ground 35 Ground 2 Data 3 36 -Card Detect 1 3 Data 4 37 Data 11 4 Data 5 38 Data 12 5 Data 6 39 Data 13 6 Data 7 40 Data 14 7 -Card Enable 1 41 Data 15 8 Address 10 42 -Card Enable 2 9 -Output Enable 43 Reserved 10 Address 11 44 -I/O Read 11 Address 9 45 -I/O Write 12 Address 8 46 Address 17 13 Address 13 47 Address 18 14 Address 14 48 Address 19 15 -Write Enable 49 Address 20 16 Ready 50 Address 21 17 +5 VDC (Analog) 51 +5 VDC (Analog) 18 Flash Card 52 Flash Card Programming Voltage Programming Voltage 19 Address 16 53 Address 22 20 Address 15 54 Address 23 21 Address 12 55 Address 24 22 Address 7 56 Address 25 23 Address 6 57 Reserved 24 Address 5 58 Reset 25 Address 4 59 -Wait 26 Address 3 60 -Input Acknowledge 27 Address 2 61 -Register Access 28 Address 1 62 Battery Voltage Detect 2 29 Address 0 63 Battery Voltage Detect 1 30 Data 0 64 Data 8 31 Data 1 65 Data 9 32 Data 2 66 Data 10 33 Write Protect 67 -Card Detect 2 34 Ground 68 Ground NOTE: Flash Card Programming Voltage (pins 18 and 51) will be any of the following voltage levels: 0, +3.3, +5.0, or +12.0 VDC. Mouse/Keyboard PIN SIGNAL PIN SIGNAL 1 Serial Data (MDATA) 4 +5 VDC (VCC) 2 No connection 5 Synchronous clock (MCLK) 3 Ground (GRND) 6 Keypad sense control (SENSE) External Connector Standard VGA video output connector supporting 31 kHz and multifrequency monitors. PIN SIGNAL PIN SIGNAL 1 Red Video 8 Ground 2 Green Video 9, 15 No connection 3 Blue Video 10 Ground 4 Reserved 11 Reserved 5 Ground 12 Reserved 6 Ground 13 Horizontal Sync 7 Ground 14 Vertical Sync Disk Drives Hard Disk Drive The main unit is equipped with one 2.5 inch, 80M or 120M IDE, ISA compatible harddisk drive with auto-park. The drive is selected for its high performance, small size, low power consumption, and high shock resistance. PIN SIGNAL PIN SIGNAL The IDE connector is a 44-pin connector (22 x 2). 1 -HOST Reset 23 -HOST IOW 2 Ground 24 Ground 3 +HOST Data 7 25 -HOST IOR 4 +HOST Data 8 26 Reserved 5 +HOST Data 6 27 Reserved 6 +HOST Data 9 28 Reserved 7 +HOST Data 5 29 Reserved 8 +HOST Data 10 30 Ground 9 +HOST Data 4 31 +HOST IRQ 14 10 +HOST Data 11 32 +HOST IOCS 16 11 +HOST Data 3 33 +HOST ADDR 1 12 +HOST Data 12 34 Reserved 13 +HOST Data 2 35 +HOST ADDR0 14 +HOST Data 13 36 +HOST ADDR2 15 +HOST Data 1 37 -HOST CS0 16 +HOST Data 14 38 -HOST CS1 17 +HOST Data 0 39 -Active 18 +HOST Data 15 40 Ground 19 Ground 41 +5 VDC 20 Reserved 42 +5 VDC 21 Reserved 43 Ground 22 Ground 44 Ground Floppy Disk Drive The computer is equipped with one 3.5, 1.44M, ISA-compatible floppy disk drive. The drive has been selected for its small size and weight, low power operation, and high shock resistance. It is capable of reading and writing 720K diskettes to maintain backward compatibility. Standard One 3.5 inch 1.44M floppy disk drive Optional None External Not supported PIN SIGNAL PIN SIGNAL 1 +5 VDC 14 -Step 2 -Index 15 Ground 3 +5 VDC 16 Write Data 4 Drive select 0 (Zero) 17 Ground 5 +5 VDC 18 Write Gate 6 Disk Change 19 Ground 7 +5 VDC 20 Track 0 (Zero) 8 Reserved 21 Ground 9 Density select 22 Write Protect 10 Motor on 23 Ground 11 Reserved 24 Read Data 12 Head Step Direction 25 Ground 13 Ground 26 Side Select (br/all-04/14/95)