Telephone Tester (430-0114) Operation Faxback Doc. # 15704 Before beginning a specific function test, perform the following steps: 1. Insert the AC Line Cord into a source of 110 - 120 volts, 60 Hz. 2. Press the POWER switch. The power indicator will light showing that power is present. 3. Press the LONG LOOP button. Initial tests will be made in this configuration. 4. If the phone or device to be tested requires the use of a separate AC adapter or other source of household AC, plug the device into one the convenient outlets located on the front apron of the Tester. Two Line Phones: To connect a two line phone to the Tester, use a 2-Line Coupler, Cat. No. 279-401. Insert the modular plug into the adapter. You can then test each line separately with each cord from the adapter. NOTE: If you wish to test a wall type telephone, insert the modular plug of the phone into a Modular Duplex Wall Phone Adapter, Cat. No. 279-359. Then insert a cord, terminating in a modular plug at each end, Cat. No. 279-374, into the bottom jack on the adapter. The free plug on the cord is then used to connect to the Tester. CORD TEST To check the total number of wires, and to verify their electrical fitness, in either the Line Cord or the Handset Cord, follow the steps below: 1. If the cords of your phone disconnect, unplug the modular line cord connector, (the wire that connects to the wall). 2. Connect both ends of the cord into the modular sockets in the test area labeled CORD TEST JACKS which is located on the upper right corner ofthe front panel. Be sure to insert the Line Cord into the jacks labeled LINE CORD. 3. Press the CORD TEST button. 4. The LED in the DISPLAY on the panel will light. Either the digit 2 or the digit 4 should be shown to indicate the number of wires in the cord. 5. At the same time either the PASS LIGHT or the FAIL LIGHT will be illuminated. If PASS lights, the cord under test is usable. If FAIL lights, replace the cord. 6. After testing the LINE CORD and re-installing it into the telephone (assuming the cord is good), remove the HANDSET CORD in a similar way. 7. Repeat Steps 1 to 6 for the HANDSET CORD, making sure to connect it to the jacks labeled HANDSET on the panel. LOOP TEST This test checks for an acceptable DC resistance value within the Switch Hook Loop. When the Handset is off-hook, the Central Office should "see" DC resistance between 57 and 600 ohms. This range is tested. 1. Reconnect LINE CORD and HANDSET CORD to the phone. 2. Plug LINE CORD into the test area labeled TEST JACKS - PHONE. 3. Press the LOOP TEST button. 4. Lift the Handset from the switch-hook. If the PASS LED lights, you are within the range of 57 - 600 ohms. If the FAIL LED lights, the phone needs service. 5. Replace the Handset on the switch-hook. If the circuit is restored to the 10 megohm level the FAIL light will go ON. If the FAIL LED was ON and now goes off or remains off, the unit requires service. DIAL TEST The following steps will check for proper output of each digit/character of either a rotary dial phone or key-pad of a pulse or tone phone. 1. Remove the Handset from the Switch-Hook. 2. Press the DIAL TEST button. 3. While watching the DISPLAY panel LEDs, dial each digit on the phone. If operational, the individual digit will be displayed. If no number or the wrong number is shown or if the FAIL lamp lights, the unit needs service. NOTE: If a tone phone is under test, the * key will display an 11. The # key will display a 12. Both PASS and FAIL lamps will be off while testing a tone phone. TRANSMIT TEST To check operation of the telephone mic: 1. Lift the Handset from the switch-hook. 2. Press the X-MIT button. 3. Speak into the microphone. 4. If the unit is functional, the PASS lamp will flicker as you speak. If NO indicator lights, the unit is defective. RECEIVE TEST To check the function of the earpiece of the phone: 1. Lift the Handset from the switch-hook. 2. Press the REC'V button. 3. Listen for a dial tone. If one is heard, the unit is working. If no tone is heard, the receiver is defective. SHORT LOOP All previous tests have been made as if the telephone was connected to distant Central Office. To test the unit as if it were trying a connection to a nearby Central Office: 1. Press the SHORT LOOP button. 2. Repeat Test 3 DIAL TEST. 3. Repeat Test 4 TRANSMIT TEST. 4. Repeat Test 5 RECEIVE TEST. 5. Arrange for service or proceed to other tests based on the criteria for passing or failing Tests 3, 4 and 5. TELEPHONE TERMINOLOGY In order to assist you to use and understand the flexibility of the tester and to translate the results of the various tests into proper action, the following overview of some typically used terms is offered. The Loop: Your phone is connected to a central office by means of a pair of wires. This pair may be relatively short (a few blocks), or much longer, such as a few miles. Usually there is a standard voltage of 50 volts DC present in your phone with the handset on the hook. If you are close to the central office, a short loop, the current might be as high as 0.08 ampere. If you are several miles away, a long loop, that current might be as small as 0.02 ampere instead. Handset: Although today the handset comes in many shapes and sizes, it is still comprised of a transmitter, into which you speak, and a receiver, from which you hear the other phone. The transmitter is typically a mic made of loosely packed carbon granules. The receiver is a miniature loudspeaker. The Hookswitch: The buttons on the cradle of your phone, are connected to a multi-contact switch inside the phone's case. When you lift the handset and the switch makes an electrical connection, it is off-hook. The phone is disconnected when the handset is on-hook. The Ringer: While electronic ringers produce sound differently and have values unique to their family of circuits, the classic ringer consisted of a gong struck by a clapper. Today, electronic circuits produce warbles, or other new sounds. The resistance of older coils are checked by the Tester. Newer circuits are similarly tested. Central Office: The switching equipment that provides local exchange telephone service for a given geographical area, designated by the first three digits of the telephone number. (llg/all-06/21/95)