TAD-1002 (430-0742) Remote Operation Faxback Doc. # 19497 You can operate the TAD from almost any touch-tone phone or from a rotary phone using a pocket tone-dialer (available at your local Radio Shack store). The TAD's remote operation security code is pre-set to 742. You can operate your TAD remotely with this code; however, we recommend that you choose and set your own code. NOTE: Do not use three identical digits (such as 999) for the security code. This could cause the TAD to malfunction. CHANGING THE REMOTE OPERATION SECURITY CODE NOTES: If the AC power fails or if the backup battery becomes weak, the remote operation security code automatically returns to 742. Be sure to set each digit within 8 seconds. Otherwise, the current time returns to the display, and you must start over from Step 1. 1. Press and hold CODE for about 2 seconds. The TAD beeps, and 742 (or the last code you set) appears on the display. The first digit flashes. 2. Press FWD or REPEAT to set the first digit, then press STOP. The second digit flashes. 3. Press FWD or REPEAT to set the second digit, then press STOP. The third digit flashes. 4. Press FWD or REPEAT to set the third digit, then press STOP. The TAD beeps once. REMOTE ANSWER ON NOTES: You must record an outgoing message before you can remotely set the TAD to answer calls. If the TAD beeps six times after answering your call, memory is full. You must erase some messages before you can set the TAD to record (see "Using Remote Commands", below). Follow these steps to remotely set the TAD to answer calls. 1. Dial your phone number. After about 10 rings, the TAD answers with a beep. 2. Enter the remote operation security code within 8 seconds. The TAD beeps twice to verify you entered the correct code. NOTE: If you do not hear two beeps immediately after entering your code, re-enter the code within 8 seconds, before the TAD disconnects your call. 3. Enter 3 1 to turn on the TAD, The TAD beeps once. USING REMOTE COMMANDS To use remote commands, you must enter the remote operation security code within 8 seconds after the TAD answers the call. After the TAD beeps twice to verify you entered the code correctly, you can enter the number(s) for the function(s) you want the TAD to perform. Press Command Function 0 Stop Stops playback, rewind, or fast-forward. 1 1 Play Plays all messages. The TAD beeps after each message. 1 2 Play Plays only new messages that have not already been played. If there are no new messages, the TAD sounds a 3-tone beep. 2 1 ANNC 1 Plays the ANNC 1 outgoing message. 2 2 ANNC 2 Plays the ANNC 2 announcement-only message. 2 3 Change ANNC 1 Records a new ANNC 1 outgoing message. When the TAD beeps, begin your new outgoing message. When you finish, press 0. The TAD beeps and plays the new outgoing message. 2 4 Change ANNC 2 Records a new ANNC 2 announcement-only message. When the TAD beeps, begin your new announcement-only message. When you finish, press 0. The TAD beeps and plays the new announcement-only message. 3 1 Answer On Sets the TAD to answer calls and record messages. 3 2 ANNC 2 Mode Sets the TAD to answer calls with an announcement and not record messages. 3 3 Answer Off Sets the TAD not to answer calls. 4 Skip During playback, press 4 to skip forward to the next message. 5 Repeat During playback, press 5 to replay the current message. 6 Review During playback, press 6 to replay previous messages. 7 Erase A Single Erases the message currently playing. Message 7 7 Erase All Erases all messages. The TAD sounds a 3-tone Messages beep if you press the wrong button or try to erase the messages before you listen to them. 8 8 Room Monitor Monitors the room where the TAD is located. After 30 seconds, the TAD beeps and monitoring stops. To continue monitoring the room, press 88 again after the beep. (EB 1/8/96)