TAD-1003 Fully Digital TAD
(430-0743)               Remote Operation             Faxback Doc. # 32074

You can operate the TAD from almost any touch-tone phone, or from a rotary
phone using a pocket tone-dialer (available at your local Radio Shack
store).  The TAD's remote operation security code is preset to 743.  You
can operate your TAD remotely with this code; however, we recommend that
you set your own code.

NOTES:  When the memory is full, the TAD answers the call after two rings
        and announces, " Memory is full."

        To bypass the outgoing message and begin recording a message
        immediately when you call the TAD from a remote phone, you can
        press * on touch tone phones (or a pocket tone dialer if you use a
        rotary phone) when the announcement begins.  The TAD skips the rest
        of the announcement, beeps once, and begins recording.

CHANGING THE REMOTE OPERATION SECURITY CODE

NOTES:  Be sure to set each digit within 8 seconds.  Otherwise, you must
        start over from Step 1.

        Do not use three identical digits (such as 999) for the security
        code.  Numbers like this are too easy for others to guess!

        If the AC power fails or if the backup battery becomes weak,
        the remote operation security code automatically resets to 743.

1.  Press and hold CODE for about 2 seconds.  The TAD beeps and the first
    digit of the preset code flashes.

2.  Press SKIP or REPEAT to set the first digit, then press STOP.  The
    second digit flashes.

3.  Press SKIP or REPEAT to set the second digit, then press STOP.  The
    third digit flashes.

4.  Press SKIP or REPEAT to set the third digit, then press STOP.  The TAD
    beeps once.

REMOTE ANSWER-ON

NOTE:  You must record an outgoing message before you can remotely set
       the TAD to answer calls.

Follow these steps to remotely set the TAD to answer calls.

1.  Dial your phone number.

    If the TAD is set to answer-off, it answers the call after 60 seconds
    and announces, "Answer off."

    If the TAD is set to answer-on, it answers after about two or four
    rings.

2.  Enter the remote operation security code within 8 seconds.  The TAD
    beeps.

3.  Press #.  The TAD beeps and announces, "Answer on."  If you do not
    enter each digit of the security code within 8 seconds, the TAD will
    disconnect.

4.  You can hang up at this point and have the TAD set to answer calls.
    If you want, you can now enter other remote command(s) (see "Using
    Remote Commands").

TOLLSAVER

If there are new messages, the TAD answers after about two rings.
Otherwise, the TAD answers after four rings.  This lets you avoid
unnecessary charges when calling by long-distance to check your messages.
If you hear more than two rings, the TAD has no new messages.  Hang up so
you will not be charged for the call.

USING REMOTE COMMANDS

To use remote commands, you must enter the remote operation security code
within 8 seconds after the TAD answers the call.  After the TAD beeps once
to verify you entered the code correctly, you can enter the number(s) for
the function(s) you want the TAD to perform.

Press    Command           Function

0   Stop                   Stops message play, message recording, and room
                           monitoring.

1   Play OGM               If an OGM is recorded, the TAD says, "Play
                           announcement" and plays the outgoing message.
                           After the message plays, the TAD beeps once.
                           If no OGM is recorded, the TAD beeps then
                           announces, "No. announcement."

2   Change OGM             Records a new outgoing message.  When the TAD
                           beeps and announces, "Record announcement,"
                           begin your new outgoing message.  When you
                           finish, press 0.  The TAD beeps.

3   Room Monitor           Monitors the room where the TAD is located.
                           The TAD announces, "Room Monitor."  After 30
                           seconds, the TAD beeps and monitoring stops.
                           To stop monitoring the room sooner, press 0.

4   Play All Messages      Plays all the recorded messages.
    (To see what commands  If messages are recorded, the TAD beeps, then
    you can use at this    announces the number of new messages before
    point, see the table   playing them.
    on Page 19.

5   Play New Messages (To  Plays only new messages that have not already
    see what commands      been played.  If new messages are recorded, the
    you can use at this    TAD beeps, then announces the number of new
    point, see the table   messages before playing them.
    on Page 19.)           If there are no new messages, the TAD beeps and
                           says, "No new message."

6   Erase All Messages     If some messages (but no new messages) are
                           recorded, the TAD sounds a long beep and erases
                           all messages.
                           If new messages are recorded, the TAD
                           announces, "New messages" but does not erase
                           all messages.
                           If no messages are recorded, the TAD beeps and
                           announces, "No Message."

#   Answer On/Off          Sets the TAD to answer or not answer calls.
                           The TAD beeps and announces, "Answer on" or
                           "Answer off."

NOTE:  The TAD sounds a 3-tone beep if you press the wrong button.

After you press 4 (to play all messages) or 5 (to play new messages), enter
the following commands you want the TAD to perform.

Press    Command           Function

6   Delete            Deletes the current message.

7   Replay Previous   Replays the previous message.

8   Replay            Replays the current message.

9   Skip              Skip forward to the next message.

0   Stop              Stops message play.


(br/all-04/19/96)