TAD-1006 Digital Answering System Telephone with Time/Day Stamp (430-0768) Remote TAD Operation Faxback Doc. # 33811 REMOTE TAD OPERATION While you are away from your home or office, you can use a touch-tone phone or a pulse (rotary) phone with a pocket tone dialer to enter your remote operation security code and do any of the following: Set the TAD to answer calls Listen to your messages Record a new announcement Delete messages Monitor the room where the TAD is located USING THE TOLL-SAVER If the TAD is set to answer in three rings or more and there are new messages (ones you have not played), the TAD answers two rings sooner than you set. For example, if you set it to answer in five rings and there are new messages, it will answer after three rings. If there are no new messages (or you set the TAD to answer in two rings or less), it answers according to the number of rings you set. This gives you time to hang up before the TAD answers and avoid unnecessary long-distance charges. To use the toll-saver, be sure the TAD is set to answer in three rings or more (see "Setting the Number of Rings" on Faxback Doc. # 32287). CHANGING THE REMOTE CODE To use your TAD-1006 from a remote telephone you must first enter a 3-digit remote operation security code. The security code for your TAD-1006 is preset to 028. You can either use the preset code, or follow these steps to change it while you are at the TAD. NOTES: If you forget your remote code after setting it, follow these steps again to set a new code. In Steps 2 and 3, you must enter your selection within 7 seconds. Otherwise, the TAD beeps three times then exits the programming mode. If this happens, start over again at Step 1. 1. Press DELETE/PROG. The TAD beeps once. 2. Press 2/Remote. The TAD beeps once. 3. Enter the new 3-digit remote operation security code. The TAD beeps once after you press each button, then it beeps twice to indicate the new code has been stored in memory. REMOTE ANSWER-ON If the TAD-1006 is connected to AC power, you can use remote phone to turn the TAD on and set it to answer calls and record messages. To remotely set the TAD to answer calls, dial your phone number and wait about 12 rings until the TAD answers. Then hang up the phone or proceed with remote operation beginning with Step 2 under "Using Remote Commands", below. After you hang up, the TAD answers calls and records incoming messages. NOTE: When the TAD is set for announcement-only, it answers calls but does not record messages. USING REMOTE COMMANDS Follow these steps to operate the TAD from a remote touch-tone phone. 1. Dial your phone number. 2. When the outgoing announcement begins, press *. The announcement stops. 3. Enter the 3-digit remote operation security code. The TAD sounds three long beeps then announces: "Press one to play back memos. Press two to play back messages. Press three to monitor the room. Press four to record a new outgoing message. Press six to skip back one message. Press seven to repeat the message. Press eight to erase the message. Press nine to skip the message. Press star (*) to stop playback or record. NOTE: If no beeps sound, re-enter the code. If you enter the correct code, but the TAD does not accept it, the code might have reset to the default (028) because of low battery power. Try entering 028 as the security code. If this works, replace the TAD-1006's backup battery and reset the remote operation security code as soon as you return to the TAD-1006's location (see "Setting the Day and Time" on Faxback Doc. # 32287 and "Changing the Remote Code" on Faxback Doc. # 33811). 4. Within 7 seconds, enter your selection (see "List of Remote Commands" on Faxback Doc. # 33811). NOTES: If you do not press a button within 7 seconds, the TAD hangs up. After you enter a remote command, the TAD is preset to beep twice after about 160 seconds then automatically hang up after about 180 seconds if you do not enter another command. If you are listening to your messages and the TAD beeps twice to warm you that it is about to hang up, you can press 7 to repeat the current message and reset the TAD's time cycle. To delete a message the first time you hear it, you must press 8 immediately after the caller's message ends (while the day/time stamp plays) but before the TAD beeps to start the next message or function. However, if you are repeating a message, you can press 8 at any time before the message ends. If your telephone line has CPC service and you hang up while the TAD is playing back the messages, it stops playback immediately and resets to answer the next calls. If you do not have CPC service and you hang up while the TAD is playing back the messages, the TAD might not recognize that you hang up. If someone calls while the TAD continues to play the message, the caller hears a busy signal. We recommend that you play all the messages or skip forward through the messages using remote commands until the TAD beeps once before you hang up. This will ensure that you hear all your messages. 5. After completing the selected function, the TAD beeps once then plays the next recorded message (if you are playing back messages) or begins re-announcing the list of selections. Enter a new command or hang up the phone. List of Remote Commands Use these keys on a touch-tone phone or pocket tone dialer to operate the TAD when you are away from your home or office. Press: To: 1 Play memo messages. 2 Play incoming messages. 3 Monitor the room where the TAD is installed. The room is monitored for 1 minute. Press 3 again to monitor for another minute. You can repeat this for as long as you like. 4 Record a new outgoing announcement. 6 Skip back to the previous message (during playback). 7 Repeat the message (during playback). 8 Delete the current message (during playback). 9 Skip forward to the next message (during playback). * (star) Stop playback of incoming messages, memos, or the outgoing announcement; end re-recording of an outgoing announcement. (LB/EB 07/02/96)