NOKIA-232 Cellular Telephone (170-1986) Operation Faxback Doc. # 34232 SWITCHING ON 1. Press and hold the ON key. The phone will carry out a short self-test briefly displaying the 'wake-up' message. (This message is programmed by your dealer, but you may change it if you wish; refer to 'Changing the wake-up message', on Faxback Doc. # 34233, for further details). When the ON indicator appears, the phone is ready for use. If the NO SVC indicator remains on then you may be outside the cellular service area, and will not be able to make or receive calls. Remember, to make or receive any calls, your phone must be switched on and in service. If you are using the SID function (refer to 'SID (Menu 18)', on Faxback Doc. # 34236, for details): When SID is switched on, and specific carriers are not available in your area, then the NO part of the NO SVC indicator may flash; in this instance you may be able to make emergency calls, but will not be able to make other calls or receive any calls. As with other radio-transmitting devices, avoid prolonged contact with the antenna when the phone is switched on. SWITCHING OFF 1. Press and hold the ON key. The display will become blank. If the charger is connected, the B indicator will remain on, and charging will continue. NOTE: Switch off the phone before removing the battery. BASIC FUNCTIONS MAKING A CALL 1. For best reception, pull the antenna up to extend fully. In areas of reasonably high signal strength you may use the phone without extending the antenna. Do not leave the antenna partly extended. 2. Enter the number you wish to dial. Remember to include the area code (if this is necessary on your system) even if you are making a local call. 3. To correct a mistake, press CLR to delete the last digit, or press and hold CLR to clear the whole display (then re-enter the number). 4. Press SEND. The IN USE indicator will appear on the display, and the number will disappear. If the NO SERVICE message appears, you are outside the cellular service area. If the NOT ALLOWED message appears, the call is barred (refer to 'Call barring [Menu 14]' on Faxback Doc. # 34236), on your phone is locked (refer to 'Locking and unlocking the phone [Menu 0]' on Faxback Doc. # 34235). You can make emergency calls even when the call barring is selected or when the phone is locked. 5. To end the call, press END. RECEIVING A CALL 1. Press any key except ON or the volume keys. An incoming call is denoted by a ringing tone and the CALL message flashing on the display. If the SILENT SERVICE option (Menu 6) has been selected there will be no ringing tone; the keypad and display lights will flash instead, and only a short beep will be heard (refer to 'Ringing volume [Menu 6]', on Faxback Doc. # 34235). If you do not answer a call, the CALL message will remain on the display (indicating a missed call); to clear the display, press any key. 'Any-key answering' facility: Any key (except ON or the volume keys) may be pressed to answer a call (except when 'keyguard' is active). If you receive a call while entering a number, the call will be answered on the first key pressed after the ringing starts. 2. To end the call, press END. ONE-TOUCH DIALING KEYS The phone is equipped with one-touch dialing keys. Simply press any one of these keys to dial the associated number (you do not need to press SEND). The following keys offer one-touch dialing. * dials the number stored in memory location 96; press and hold the key for 2 seconds. You may store any number in this location. # dials the number stored in memory location 97; press and hold the key for 2 seconds. You may store any number in this location. 9 dials the emergency number (programmed by your dealer); press and hold the key 2 seconds. This function will not operate if keyguard is active or if the 'Emergency number key' function (Menu 13) is set to 'Off'. The emergency number is programmed by your dealer, and stored in a special location; you cannot change this number, neither can you recall the number to the display without dialing the number (if you press STO or RCL then hold 9, you will dial the emergency number). Refer to 'Making Emergency Calls', below. (letter symbol) dials the number stored in memory location 98. This location may already contain your voicemail number string, but you may store any number in this location (e.g. if you are not a subscriber to voicemail). Refer to 'Using voicemail/favorite number', below, for further details. NOTE: When keyguard is activated, none of these keys are operational for one-touch dialing. When in a call, the *, # and 9 keys do not operate as one-touch dialing keys; instead, they revert to their normal (DTMF tone-dialing) functions. When in a call, the (letter symbol) key does not operate to make a further call. Instead, pressing this key would force DTMF data to be sent if there is data (e.g. starting with a 'w' (wait) character) waiting to be sent. For example, the string stored in voicemail memory location 98 might contain the voicemail phone number, then a 'w' and some DTMF data; once a call to the voicemail number has been established, a second press of the (letter symbol) key will send the DTMF data. You may link any memory location to a one-touch dialing key; this will enable you to dial the phone number stored in that location, by simply pressing the key. To do this, store the number of the memory location (i.e. one or two digits only) to be linked, in any of the one-touch dialing memory locations. For example, to link the number stored in memory location 33 to the (letter symbol) key, store '33' in memory location 98 (voicemail/ favorite number); then, when you press (letter symbol), the phone number in memory location 33 will be dialed automatically (speed dialed). This function has the following benefit: You may change the 'favorite' number which is dialed when the (letter symbol) key is pressed; e.g. you may keep several such numbers in normal memory locations, and select the required number by simply storing its location number in location 98, as required. This is preferable to copying contents that exist in other locations to location 98, as this cannot be done when the contents has a name (any particular name can be stored in only one location). MAKING EMERGENCY CALLS You nay make emergency calls even if the 'keyguard' function is on, or if the phone is locked. There are two methods. Either Enter the emergency number (e.g. certain areas of the USA enter 911), then press SEND. This method can be used regardless of whether the phone is locked, or if keyguard is active. or Press 9 for two seconds. NOTE: This method cannot be used if keyguard is active, or if this one-touch dialing function has been set to off using the 'Emer- gency-number Key' function (Menu 13), on Faxback Doc. # 34236. Otherwise, holding the 9 key down for 2 seconds or more, at any stage in any key-entry operation (but not when already in a call), will dial the emergency number. The emergency number is programmed by your dealer. You cannot change this number, or recall the number to the display without the number. Emergency numbers differ from one country to another; and within countries, if necessary, contact the local network operator to obtain the number for your area. When making an emergency call, remember to give your name and mobile phone number, as well as the location of the incident. Remember that your phone may be the only means of communication at the scene of an accident; don't cut off the call until given permission to do so. MAKING INTERNATIONAL CALLS To make an international call, either dial the number in the normal way (i.e. starting with the international prefix), or use the built-in quick method, utilizing the internationally-recognized '+' character; '+' is available on the * key. To use the quick method: Press * * ('+' will be displayed), instead of entering the international prefix, then dial the remainder of the number. For example, calling a UK number can be done by entering a number starting '* * 4 4'. When sent, the international prefix (for the NAM currently selected) will be generated automatically. Note, however, that if you store a number using the international prefix '+', then when recalled it will be displayed with the appropriate dialing code. ADJUSTING THE EARPIECE VOLUME On the side of the phone, press /\ to increase or \/ to decrease the volume (to one of five levels). After pressing either key, the selected volume level is indicated on the display; e.g. VOLUME 1 indicates the lowest level, and VOLUME 5 indicates the highest. A warning beep will be heard if you try to decrease the volume below level 1, or increase it above level 5. NOTE: If using the handsfree option, the handsfree volume will be adjusted The volume levels for the phone, and for the handsfree option, are stored independently. LAST NUMBER REDIAL The phone stores (automatically) the last five numbers (together with any associated names) which you have called or attempted to call. Numbers previously stored are sequentially overwritten by each new one (if it differs from the previous); the last-called number replaces the earliest stored number. To make a call to the number you called last: Ensure the display is clear, then press SEND. The number will appear on the display (unless memory location 00, where the last-called number is stored, is empty). To make a call to any of the other (four) last-dialed numbers: 1. Press O RCL. 2. Press /\ and \/ to scroll the numbers (i.e. in locations 00 to 04), until the desired number is displayed. 3. Press SEND to make a call to the number displayed. Using menu 10, you can set the group of last-dialed numbers to be either cleared or retained when the phone is switched off. USING VOICEMAIL/FAVORITE NUMBER The (letter symbol) (voicemail) key is designed to allow access to your voicemail (or favorite number) simply by pressing the key once (there is no need to press SEND). Once a call is established, a second press of this key will send a PIN number (or DTMF string) if this has been stored. The voicemail/favorite number facility uses the number stored in memory location 98. You may store any number in this location, if you do not wish to use the voicemail facility. Whatever number is in location 98 will be dialed automatically when (letter symbol) is pressed. A typical voicemail number string would be: '222w3333', where '222' is the system-dependent voicemail number, 'w' is the wait character (this is entered by pressing * * * *), '3333' is your voicemail PIN code (which would be sent after the second press of the [letter symbol] key). Please note that the voicemail service is a system feature, and may not be available on your network. To be able to use voicemail, it must be available on your network, and you must be a subscriber to this service. For further details, ask your network provider. For specific operating instructions refer to the appropriate documentation which may be issued by your network provider. AUTOMATIC NUMBER GROUPING In order to make displayed telephone numbers easier to read, the phone automatically splits each number into groups. Once you have entered a complete telephone number from the keyboard or have recalled one from the keyboard, or have recalled one from memory, then usually: - the area code will be displayed on the top line, and - the subscriber number will be displayed on the lower line (a 7-digit number will be split into 3 digits and 4 digits). Longer numbers, such as international or special service numbers, will not be grouped, but shown aligned to the right with no spaces. SPEED DIALING Speed dialing is the quickest way to recall and dial a number, and is particularly useful for frequently-used numbers. You can speed dial any number already stored in a memory location either by entering the location number or the name stored with the number to be called. 1. Enter the number of the memory location containing the number to be dialed (e.g. 2). Alternatively, press ABC (to select alpha mode), then enter the name stored with the number to be dialed. 2. Press SEND. The phone will recall the number/name from memory, display it briefly, then dial the number. If the memory location contains no number, or the name was not found, then no call attempt will be made. If the memory location is empty, the message EMPTY (if the number mode) or NOT FOUND (if in alpha mode) will be displayed. SIGNAL STRENGTH INDICATION The signal strength indicator (on L.H. side of the display) shows received signal strength. The indicator consists of a number of bars; the more bars showing, the stronger the signal. The quality of your call depends on the signal strength of the cellular signal in your area. If the signal is poor, try moving to a different position or extend the antenna. If you are using the phone in a building, you may find that reception is better near a window. (LB/EB 07/19/96)