Motorola DPC-550
(170-1059)                 Programming                Faxback Doc.# 9583

Your phone should be programmed by a trained technician when you purchase
your phone.  The following information must be assembled from the carrier
before programming a phone:

       Customer Cellular Phone Number     (_ _ _)_ _ _- _ _ _ _
       Carrier System ID                   _ _ _ _ _
       Carrier Access Overload Class       _ _
       Carrier Group ID                    _ _
The battery must be charged to program the phone.  The AC charger adapter
is NOT sufficient to program or operate the phone with a discharge battery.

START  Press [PWR] ON
       Press [FCN], 0 000000 000000 (13 zeros or 0+security code 2x), [RCL]
       NOTE:  You will not see any zeros in display.

STEP 1 Display shows 01
       Press [<*]
       Display shows 00000; Enter your Carrier System ID _ _ _ _ _

Step 2 Press [<*], Display shows 02
       Press [<*]
       Display shows 111; Enter Customer area code _ _ _.

Step 3 Press [<*], Display shows 03
       Press [<*]
       Display shows 1110111; Enter Customer phone number _ _ _ _ _ _ _.

Step 4 Press [<*] [<*] [<*], Display shows 05
       Press [<*]
       Display shows 00; Enter Carrier Access Overload Class _ _.

Step 5 Press [<*], Display shows 06.
       Press [<*]
       Display shows 00; Enter Carrier Group ID _ _.

*If you wish to change the security code, the unlock code, or program a
second telephone number continue to step 6, otherwise press [<*] until 01
is shown in the display.  Verify all data you have entered by following
steps 1-5.  When display shows 07, press [SND].  DO NOT press [SND] until
all data has been verified.

Step 6 Press [<*], Display shows 07
       Press [<*]
       Display shows 000000; Enter desired six-digit security code or go to
       step 7.
       
       Note: It is not advised to change the security code from the factory
             preset of 000000. If the new code is forgotten, the phone
             will have to be sent to a certified repair center at a charge
             to be reset.

Step 7 Press [<*], Display shows 08.
       Press [<*]
       Display shows 123; Enter desired three-digit unlock code to go to
       step 8.

       Note: The unlock code can be changed after programming as described
             under Security Features. If the unlock code is forgotten, you
             can enter programming gain to verify.

Step 8 Press [<*] [<*] [<*], Display shows 10.
       Press [<*]
       Display shows 011100; Enter 011110 if a second phone number is
       desired or continue.

       Before you program your second phone number according to the  
       instructions on the back side, assemble all necessary information
       for that number as outlined at the top of this page.

DATA   Press [<*] until 01 is shown in display.  
CHECK  Verify all data you have entered by following Steps 1-8.
       When display shows 11, press [SND].
       (If you chose to activate a second phone number in step 8, see
       instructions on the back side.)
       DO NOT press [SND] until all data has been verified.

Phones Can Only Be Programmed 3 Times to Insure Security.


SECOND PHONE NUMBER PROGRAMMING INSTRUCTIONS

To program a second telephone number, you must enter 011110 for Step 8
when programming the first number.  Once you have reached Step 01, after
verifying the data, press [SND] and the following programming steps for
the second telephone number will appear.

Step 1 Display shows 012
       Press [<*]
       Display shows 00000; Enter your Carrier System ID _ _ _ _ _

Step 2 Press [<*]
       Display shows 022
       Press [<*]
       Display shows 111; Enter Customer area code _ _ _

Step 3 Press [<*]
       Display shows 032
       Press [<*]
       Display shows 1110111; Enter Customer phone number _ _ _ _ _ _ _

Step 4 Press [<*]
       Display shows 042
       Press [<*]
       Display shows 00; Enter 14

Step 5 Press [<*]
       Display shows 052
       Press [<*]
       Display shows 00; Enter Carrier Access Overload Class _ _

Step 6 Press [<*]
       Display shows 062
       Press [<*]
       Display shows 00, Enter Carrier Group ID _ _

NOTES  If a mistake is made, press [CLR] and re-enter data or turn power 
       off to begin again.

       After verifying all data by press [<*] through steps 1-6, press
       [SND] when you've returned to Step 01.  That will complete the
       programming of the phone.

       DO NOT PRESS [SND] until all data has been verified.


(CS 1/22/96)