Motorola 12822 (170-1058) Programming Faxback Doc. # 9742 Before programming the phone, be sure you have this information: Customer Cellular Telephone Number: (_ _ _) _ _ _-_ _ _ _ Carrier System ID: _ _ _ _ _ Carrier Access Overload Class: _ _ Carrier Group ID: _ _ The battery must be charged. The AC charger is NOT sufficient to operate the phone with a discharged battery. Mobiles must be connected to a power source. Note: If you make a mistake while programming, press CLR and re-enter the data, or turn off power to begin again. Follow these steps to program the phone: 1. Press PWR on, FCN, and either 13 zeroes or 0 + the security code twice, then press RCL. Note: You will not see any zeroes on the display before you press RCL. The display shows 0 1. 2. Press *. The display shows 0 0 0 0 0. Enter the 5-digit Carrier System ID and press *. The display shows 0 2. 3. Press *. The display shows 1 1 1. Enter the customer's 3-digit area code and press *. The display shows 0 3. 4. Press *. The display shows 1 1 1 0 1 1 1. Enter the customer's 7-digit phone number and press * * *. The display shows 0 5. 5. Press *. The display shows 0 0. Enter the 2-digit Carrier Access Overload Class and press *. The display shows 0 6. 6. Press *. The display shows 0 0. Enter the 2-digit Carrier Group ID. Note: If you wish to change the security code, the unlock code, or program a second number, continue to Step 7. Otherwise, press * until the display shows 0 1. Follow Steps 2-6 to verify the data you have entered. When the display shows 0 7, press SND. Caution: Do not press SND until you have verified all the data. 7. Press *. The display shows 0 7. Press * again. The display shows 0 0 0 0 0 0. Enter the desired 6-digit security code or go on to Step 8. Caution: We do not recommend changing the security code from the factory preset of 000000. If the new code is forgotten, the phone must be sent to a certified repair center to be reset. 8. Press *. The display shows 0 8. Press * again. The display shows 1 2 3. Enter the desired 3-digit lock code or go on to Step 9. Note: The unlock code can be changed after programming as described in the Owner's Manual under "Security Features." If the unlock code is forgotten, you can enter programming again to verify. 9. Press * * *. The display shows 1 0. Press * again. The display shows 0 1 1 1 0 0. If you wish to program a second phone number, enter 0 1 1 1 1 0 and follow the instructions under "Programming a Second Phone Number." Otherwise, go on to Step 10. 10. Press * until the display shows 0 1. Follow Steps 2-9 to verify all the data you have entered. When the display shows 1 1, press SND. Caution: Do not press SND until you have verified all the data. Programming a Second Phone Number Before you program a second phone number, you must enter 0 1 1 1 1 0 for Step 9 when programming the first number. After you press SND in Step 10 when programming the first number, the display shows 0 1 2. Follow these steps to program a second phone number. Note: Be sure you have all necessary information for the second number available. 1. Press *. The display shows 0 0 0 0 0. Enter the 5-digit Carrier System ID and press *. The display shows 0 2 2. 2. Press *. The display shows 1 1 1. Enter the customer's 3-digit area code and press *. The display shows 0 3 2. 3. Press *. The display shows 1 1 1 0 1 1 1. Enter the customer's 7-digit phone number and press *. The display shows 0 4 2. 4. Press *. The display shows 0 0. Enter 1 4 and press *. The display shows 0 5 2. 5. Press *. The display shows 0 0. Enter the 2-digit Carrier Access Overload Class and press *. The display shows 0 6 2. 6. Press *. The display shows 0 0. Enter the 2-digit Carrier Group ID. 7. Repeat Steps 1-6 to verify the data until the display shows 0 1. Then press SND. This completes programming of the phone. Caution: Do not press SND until you have verified all the data. (JLC/all-02/13/95)