6 in 1 RF Remote Control System (150-1919) Operation Faxback Doc. # 18621 SET UP AND OPERATION OF THE 6 IN 1 RF REMOTE CONTROL SYSTEM'S RF COMMAND CONSOLE Once you have properly set up your 6 in 1 RF Remote Control System's remote control you can operate your IR remote controlled devices from anywhere in your house, by following these instructions. 1. Plug the RF Command Console into any AC outlet and fully extend its antenna. 2. Point the front of the command console towards the device (TV, VCR, CD player,...) that you want to control. 3. Use the buttons on the remote just like you would your IR controlled devices (TV, VCR, cable box, ...) To control your IR controlled devices that your 6 in 1 RF Remote Control System RF command console is pointed towards, simply press the appropriate device key on your 6 in 1 RF Remote Control System remote (TV, VCR, cable,...) and then the desired function key. This can be done from anywhere in your home. Controlling Lights and Appliances The Plug 'n Power feature allows you to control lamps and appliances with your 6 in 1 RF Remote Control System's remote control and RF command console. You will need Plug 'n Power light modules and appliance modules to use this feature. The Plug 'n Power modules are available at your local Radio Shack store. To control Plug 'n Power modules with the 6 in 1 RF Remote Control System's remote control or manually from your Radio Shack 6 in 1 RF Remote Control System's RF command console, follow these instructions: 1. Set the house code dial located at the top of the RF command console to the same letter as Plug 'n Power modules. 2. Set the bank switch on the RF command console for the group of modules you want to control (1, 2, 3, 4 or 5, 6, 7, 8). With the switch in the 1-4 position, module numbers 1, 2, 3, and 4 can be controlled. When the switch is in the 5-8 position, modules 5, 6, 7, 8 can be controlled. 3. Now press the Plug 'n Power key on your Radio Shack 6 in 1 RF Remote Control System's remote control. 4. To turn all light modules on with the remote control, once the command console and the Plug 'n Power modules are set, press the All Lts On key (PWR). You may also press the LIGHTS ON key on the command console to turn on all light modules directly from the command console. NOTE: This affects all lamp modules and wall switch modules which are set to the same house code as the command console. 5. Press the All Off key on the Remote Control System remote or the UNITS OFF button on the command console to turn off all light and appliance modules. NOTE: This affects all lamp and appliance modules set to the same house code as the command console. 6. To turn on or off specific lamps and appliances first, set the bank switch to the 1-4 or 5-8 position for the group of modules you want to control. Press the appropriate digit key for the selected module (1, 2, 3, 4, or 5, 6, 7, 8). Press the On or Off key on the remote control and the appropriate console will respond. To control specific lamps and appliances directly from the RF command console, press the top button of the corresponding module number (1, 2, 3, 4 or 5, 6, 7, 8) to turn the module on. Press the bottom button to turn the module off. 7. To dim lights connected to lamp modules, and wall switch modules, turn on the console as shown in Step 6 above. Then press and hold the DIM or BRIGHT key on the Remote Control System remote or RF command console. When the desired brightness is reached, simply release the key. TURNING THE RCA DSS SYSTEM ON: 1. Press Cable Key. 2. Press SETUP Key 2 blinks. 3. Enter 994. 4. Press SETUP and release. 5. Enter 483. 6. Press SURROUND Key. The SURROUND Key is programmed to turn on the RCA DSS Satellite System. Power will turn it off. Display Source Selection 1. Press TV button. 2. Press SETUP 2 blinks. 3. Enter 994. 4. Press and release SETUP button. 5. Enter 635. 6. Press VIDEO SEQ. VIDEO SEQ button will now control the input source, Video 1, Video 2, or Antenna. (IR/ir-06/19/96)