DMP 2104 (26-2865)            Control Panel            Faxback Doc. # 4189

This printer has no DIP switches; instead, it has non-volatile memory. 
Whether the printer is turned on or off, it remembers various printer sett-
ings.

Each of the four buttons on the control panel functions as it is labeled.
These buttons are defined as follows:

        ┌──┐ ┌──┐ ┌──┐ ┌──┐ ▄▄ Power Indicator
        │  │ │  │ │  │ │  │ ▄▄ On Line/Alarm Indicator
        └──┘ └──┘ └──┘ └──┘ ▄▄ LQ Indicator
          │    │    │    │
 On/Off ──┘    │    │    └── LQ/Draft Switch
 Line Switch   │    └── Form Feed Switch
               └── Line Feed Switch

To check or change the settings now in memory, the printer must be in the 
setup mode. Setup mode allows you to select options that change the printing 
style, page format, and other settings. Before you enter the setup mode, be 
sure to load paper that is at least 8 inches wide because the current sett-
ings will print out.

Note that the setup mode has two levels.

° Function Select Mode
° Menu Select Mode

┌─────────────────────────────────┐
│The control panel in Setup Mode: │
└─────────────────────────────────┘

[ON/OFF LINE] - turn on the printer while holding down this switch to enter 
                the setup mode.  Or, if the printer is already on, be sure 
                the printer is off line and there is no data in buffer.  
                Press and hold [ON/OFF LINE] and then press [LINE FEED] to 
                enter setup mode.

Note: Press in the setup mode switches to switch between the function select
      mode and the menu select mode.

[LINE FEED]   - press to advance to the next item in the current mode. Once 
                through the entire list of items, the program repeats the
                list.

[FORM FEED]   - press to go back to the previous item in the current mode.
                Once through the entire list of items, the program repeats 
                the list.

[LQ/DRAFT]    - press to exit the setup mode and return to the normal print
                mode.

ON LINE/ALARM - remains lighted during the function select mode; goes off
Indicator       during the menu select mode.

┌───────────────────────┐
│Setup Mode Operations: │
└───────────────────────┘

1.  To enter setup mode, press and hold [ON/OFF LINE] while you turn on the
    printer. Or, if the printer is already on, be sure that the printer is
    off line and there is no data in the buffer. Press and hold [ON/OFF LINE]
    and then press [LINE FEED] to enter setup mode. The printer prints the
    current settings, followed by the first function (EMULATION) and its
    current menu  setting. Now the printer is in the function select mode.
    The ON LINE/ALARM indicator lights.

Note: If there is data in the buffer, the ON LINE/ALARM indicator flashes 
      and the printer does not enter the setup mode.

2.  Press [LINE FEED] or [FORM FEED].  Each time you press one of these
    buttons, the selected function and its current menu setting print. Press
    as many times as necessary until the function you want to change prints.

3.  When the desired function prints, press [ON/OFF LINE] to switch to the
    menu select mode.  The ON LINE/ALARM indicator goes off.

4.  Press [LINE FEED] or [FORM FEED] until the menu you want prints.

5.  If you need to change any other functions, press [ON/OFF LINE] to enter
    the function select mode and repeat Steps 2,3,and 4.

6.  When you finish changing the menu settings, press [LQ/DRAFT]. The printer
    memorizes your new settings, exits the setup mode, and enters the normal
    on-line print mode.

Note: If you turn off the printer without pressing [LQ/DRAFT], the printer
      does not save your new settings.