DMP 106 (260-2802)             Settings               Faxback Doc. # 4408

There are four switches located on the left rear side of the printer. These
switches allow you to customize some of the DMP-106 features for your own
applications.

When you set switch 1 to OFF before turning the DMP-106's power ON, the
DMP-106 selects Tandy codes. In this setting, the switches function as 
shown in Table 1. On the other hand, if you set switch 1 to ON, the DMP-106
selects codes for IBM. In this case, the switches function as shown in 
Table 2. For instance, in Tandy mode, you can select different baud rates 
and interface modes.

REMEMBER!! THE PRINTER POWER MUST BE OFF BEFORE YOU CHANGE ANY OF THE
SWITCHES.


┌───┬───┬─┬───┬─┬───┬─┬───┬───┐         ┌───┬┬─┬┬─┬───┬─┬───┬─┬───┬───┐
│ON │   │ │   │ │   │ │   │   │         │ON │└─┘│ │   │ │   │ │   │   │
│ ^ │┌─┐│ │┌─┐│ │┌─┐│ │┌─┐│   │   /\ ON │ ^ │   │ │┌─┐│ │┌─┐│ │┌─┐│   │
│ │ └┴─┴┘ └┴─┴┘ └┴─┴┘ └┴─┴┘   │    │    │ │ └───┘ └┴─┴┘ └┴─┴┘ └┴─┴┘   │
│ │   1     2     3     4     │    │    │ │   1     2     3     4     │
│ │                           │    │    │ │                           │
│                             │    │    │                             │
└─────────────────────────────┘   \/ OFF└─────────────────────────────┘

     (In Tandy Mode)                         (In IBM Mode)

TABLE 1. DIP SWITCH FUNCTION IN TANDY MODE (SWITCH 1 SET TO OFF)

POSITION   │SYMBOL             │ON                     │OFF
───────────┼───────────────────┼───────────────────────┼───────────────────
   1       │Control codes      │                       │Tandy Codes
───────────┼───────────────────┼───────────────────────┼───────────────────
   2       │Serial/Parallel    │Serial Interface       │Parallel Interface
───────────┼───────────────────┼───────────────────────┼───────────────────
   3       │600/1200 BPS       │600 BPS in Serial      │2400 BPS in Serial
           │                   │Interface              │Interface
───────────┼───────────────────┼───────────────────────┼───────────────────
   4       │CR                 │Carriage Return Only   │Carriage Return and
           │                   │(CR = CR)              │Line Feed (CR = NL)
───────────┴───────────────────┴───────────────────────┴───────────────────

TABLE 2. DIP SWITCH FUNCTION IN IBM MODE (SWITCH 1 SET TO ON)

POSITION   │SYMBOL             │ON                     │OFF
───────────┼───────────────────┼───────────────────────┼───────────────────
   1       │Control codes      │Codes for IBM          │      
───────────┼───────────────────┼───────────────────────┼───────────────────
   2       │LF                 │Line Feed Only (LF=LF) │Line Feed & 
           │                   │                       │Carrige Return 
           │                   │                       │(LF=NL)
───────────┼───────────────────┼───────────────────────┼───────────────────
   3       │Character Set      │Character Set 2        │Character Set 1
───────────┼───────────────────┼───────────────────────┼───────────────────
   4       │CR                 │Carriage Return Only   │Carriage Return and
           │                   │(CR = CR)              │Line Feed (CR = NL)
───────────┴───────────────────┴───────────────────────┴───────────────────
           
(abo/tmc-05/24/95)