6 Disc CD Changer System
(120-2180)                    Installation            Faxback Doc. # 17103

BEFORE YOU BEGIN THE INSTALLATION

Before you install the CD changer's components, read all the instructions
in this owner's manual.  You should be able to answer all of these
questions about the vehicle's electrical and sound systems.

    Can my vehicle's sound system tune FM broadcasts?

    Does my vehicle's sound system have an antenna jack?

    Which terminal in my vehicle's fuse box is for accessories?

    How do I connect a wire to the fuse box?

    Which of the CD changer's wires is the power system?

    Does my vehicle have a 12-volt negative ground system?

NOTE:  Installation in your vehicle might require cutting or modifying
       your vehicle.

In addition to the supplied hardware kit, you will need the following items
to install the CD changer:

    Cable ties or electrical tape

    Isopropyl alcohol

    Small- and medium-sized Phillips screwdrivers

CHOOSING/PREPARING THE MOUNTING AREAS

The CD changer plays CDs through your vehicle's existing sound system.  The
supplied FM modulator converts the CD changer's sound to an FM signal so
you can hear it by tuning your vehicle's stereo to an FM frequency.  You
use the supplied commander to control many of the CD changer's functions.

Follow these steps before you mount the CD changer's components.

1.  Choose locations for mounting the CD changer and its components where:

    You can easily reach them.

    Wires and cables will not interfere with the vehicle's pedals or other
    moving parts.

    No component is directly in front of heating vents.

    All wires and cables will reach their connection points.

2.  Confirm that the CD changer and its components will fit the mounting
    areas you select.

CAUTION:  Be careful to avoid obstructions behind all mounting surfaces.


CD CHANGER

You can mount the supplied CD changer horizontally, at a 45-degree angle,
or vertically in your vehicle's trunk, on the floorboard, or under a seat.

CAUTION:  Do not mount the CD changer upside down.

NOTES:  The CD changer's mounting area must be at least 13 inches (33 cm)
        deep.

        When you choose a mounting area for the CD changer, make sure it is
        close enough to the FM modulator's mounting area so you can connect
        both components with the supplied CD changer cable.  The cable is
        about 16 feet (4.87 m) long.

        Do not mount the CD changer anywhere in your vehicle that is
        exposed to direct sunlight (such as the front or rear deck) or
        extreme heat (such as the engine compartment).  Direct sunlight
        or extreme heat can damage CDs and the CD changer.

        Make sure your vehicle's mounting area is as level as possible.  If
        you cannot mount the CD changer exactly level, make sure the CD
        changer will not tilt more than 15 degrees from the horizontal,
        45-degree, or vertical mounting positions.

        Make sure there is enough room for you to insert and remove the
        supplied CD magazine from the CD changer.

FM MODULATOR

You can mount the supplied FM modulator under your vehicle's dashboard.

NOTES:  The FM modulator's mounting area must be at least 7 inches
        (17.7 cm) wide by 3 1/4 inches (8.25 cm) deep.

        When you choose a mounting area for the FM modulator, make sure
        it is close enough to your vehicle's ground, power, and sound
        system so you can connect them with the FM modulator's wires and
        plugs (see "Making the Connections").

COMMANDER

For ease of use, you can mount the supplied commander on the dashboard
using the supplied hook-and-loop fastening tape.

NOTE:  When you choose a mounting area for the commander, make sure it is
       close enough so the FM modulator's mounting area so the commander's
       cord will reach the FM modulator.  The commander's cord is about 5
       feet (1.52 m) long.

REMOVING THE SHIPPING SCREWS

The shipping screws help protect the CD changer from damage during
shipment.

Before you mount the CD changer, use a small Phillips screwdriver to remove
the four shipping screws from the bottom of the CD changer.

CAUTION:  If you do not remove the shipping screws from the CD changer,
          it will not work.

HINT:  Save the shipping screws in case you ever have to move the CD
       changer to another vehicle.  You can secure them to the back of
       the CD changer with a piece of tape.