2800HD  
(250-3550)         Using the SETUP_28 Utility         Faxback Doc. # 1844

The setup program is found on MS-DOS diskette # 1.

┌────────────────────────┬──────────────────────┬─────────────────────────┐
│       Date & Time      │      Start Up        │      Serial Ports       │
├────────────────────────┼──────────────────────┼─────────────────────────┤
│    Date [11/14/1990]   │   Initial Program    │   Port 1    [Enabled ]  │
│    Time [11:22:34]     │     [DeskMate]       │   Port 2    [Disabled]  │
│                        │                      │   Addresses [Normal  ]  │
├────────────────────────┼──────────────────────┼─────────────────────────┤
│         Speed          │     Num Lock Key     │        Timeouts         │
├────────────────────────┼──────────────────────┼─────────────────────────┤
│                        │                      │                         │
│     CPU [ 6] MHz       │     Light [ON ]      │  Backlight  [00] Minutes│
│                        │                      │  LCD        [00] Minutes│
│                        │                      │  Hard Drive [02] Minutes│
├────────────────────────┴──────────────────────┴─────────────────────────┤
│<ESC> Exit to DOS without saving setup   <CTRL_BRK> Reboot without saving│
│<F1> Help for option that cursor is on       <SPACE> Toggles options     │
│<F2> Save setup and exit                     <ARROW> Moves to next option│
└─────────────────────────────────────────────────────────────────────────┘

The following settings are stored inside the computer, regardless of
whether it is turned on or off:

- Date
- Time
- Startup environment (MS-DOS or DeskMate)
- Serial Port 1/2  enable/ disable
- CPU speed (12 or 6 MHz)
- NUM LOCK on or off at startup
- Elapsed idle time before the hard drive enters standby mode
  (0-18 minutes)
- Elapsed idle time before the backlight enters standby mode
  (0-60 minutes)
- Elapsed idle time before the LCD display enters standby mode
  (0-60 minutes)

Using the SETUP_28.COM utility, you can change any of the preceding
settings as desired.  You MUST use setup if you install or remove memory,
a modem, mouse, or other external serial device.
 
Date and Time: 
   
    Adjust the date and time.  Used by the system for files.

Startup Environment:

    Choose whether DeskMate or MS-DOS C> prompt are the first environment 
    displayed at startup.

NUM LOCK Key:

    If an external keyboard is connected to the computer, its NUM LOCK 
    function can be activated automatically at startup.  Select Light ON to 
    activate the NUM LOCK function.

Standby Mode:

    Select the amount of idle time that must pass before a device turns 
    itself off. (For maximum battery time, use the recommended settings.)

    * The backlight will turn off after an idle period of up to 60 minutes 
      (default = 4).
    * The built-in display will turn off after an idle time of up to 18 
      minutes (default = 8).
    * The hard drive will turn off after an idle period of up to 18 minutes 
      (default = 2).

Serial Ports:

    There are 2 serial ports: the modem port (called the internal port) and 
    the external serial port. Enable port 1 if you connect an external 
    device (ex. a mouse) to the external serial port. Enable port 2 if you 
    install an internal modem.  To conserve power, disable the ports if no 
    option is installed in it.

Note:  You can swap ports (make the modem port 1) by selecting SWAPPED under 
the address option.

CPU Speed:

    Select either 12 or 6 MHz.  Some applications run better at 6 MHz.


(jej/tmc-12/02/95)