1100 FD (250-3530) Using the SETUP_11 Utility Faxback Doc. # 1993 The setup program is found on the MS-DOS diskette. Machine Startup: MEMORY DIAGNOSTICS ON START-UP NO SERIAL PORT ASSIGNMENT PRIMARY:RS-232C, SECONDARY:MODEM PRIMARY START-UP DEVICE ROM DOS Startup: INITIAL START-UP PROGRAM DESKMATE AUTOMATIC PROMPT FOR DATE AND TIME NO NUMBER OF DISK BUFFERS (2-17) 10 MAXIMUM # OF OPEN FILES (8-23) 10 CHECK FOR CONFIG.SYS ON DRIVE A: CHECK FOR AUTOEXEC.BAT ON DRIVE A: Power Management: AUTOMATIC FLOPPY DISK STANDBY ENABLE DISPLAY TIMEOUT INTERVAL 8 MINUTES LOW POWER BEEPER ENABLE F1 TO UPDATE F10: FACTORY SETTINGS Changing Computer Functions: Run the program by typing Setup_11 Use the up and down arrows to select the item you want to change. Then, press the left and right arrows to select the option for the item. When you have selected all options, press to save your changes. If you do not want to save changes, press . If you want to restore all options to the factory settings, press . You must reset your computer for the changes to take affect. The following chart outlines the function of each option: ┌─────────────────────────────────┬────────┬──────────────────────────────┐ │ SELECTION │ OPTION │ COMMENT │ ├─────────────────────────────────┼────────┼──────────────────────────────┤ │MEMORY DIAGNOSTICS ON STARTUP │NO │Usually leave set to NO. Set │ │ │YES │to YES only if you suspect │ │ │ │memory problems. │ ├─────────────────────────────────┼────────┼──────────────────────────────┤ │SERIAL PORT PRIMARY ASSIGNMENTS │See the │Lets you switch the PRIMARY │ │ │screen │(Com1:) and SECONDARY │ │ │ │(Com2:)port assignment. │ ├─────────────────────────────────┼────────┼──────────────────────────────┤ │PRIMARY STARTUP DEVICE │ROM │Lets you force the computer │ │ │DISK │to boot from the floppy drive │ │ │ │Some programs require this. │ ├─────────────────────────────────┼────────┼──────────────────────────────┤ │INITIAL STARTUP PROGRAM │ROM │Lets you select what the com- │ │ │DISK │puter runs at startup. │ ├─────────────────────────────────┼────────┼──────────────────────────────┤ │AUTOMATIC PROMPT FOR DATE AND │NO │Lets you select to manually │ │TIME │YES │enter the date and time. │ │ │ │Usually set to NO. Set to YES │ │ │ │if you need to change the sys-│ │ │ │tem date or time. │ ├─────────────────────────────────┼────────┼──────────────────────────────┤ │NUMBER OF DISK BUFFERS │2-17 │Default value of 10 should be │ │ │ │adequate for most programs. │ │ │ │Changes only if your program │ │ │ │requires more. │ ├─────────────────────────────────┼────────┼──────────────────────────────┤ │MAXIMUM # OF OPEN FILES │8-23 │Default value of 10 should be │ │ │ │adequate for most programs. │ │ │ │Change only if your program │ │ │ │requires more. │ ├─────────────────────────────────┼────────┼──────────────────────────────┤ │CHECK FOR CONFIG.SYS ON DRIVE │NO │Some programs require you to │ │ │A: │load special drivers. These │ │ │ │drivers load from the Config. │ │ │ │Sys file on the diskette upon │ │ │ │startup. │ ├─────────────────────────────────┼────────┼──────────────────────────────┤ │CHECK FOR AUTOEXEC.BAT ON DRIVE │NO │You can have the computer ex- │ │ │A: │ecute this special batch file │ │ │ │on a diskette upon startup. │ │ │ │See the MS-DOS Ref. Guide for │ │ │ │info. on using this feature. │ ├─────────────────────────────────┼────────┼──────────────────────────────┤ │AUTOMATIC FLOPPY DISK STANDBY │ENABLE │Lets the computer place the │ │ │DISABLE │floppy drive on standby when │ │ │ │the programs are not accessing│ │ │ │it. This slightly increases │ │ │ │the time needed for disk oper-│ │ │ │ations,but saves battery power│ ├─────────────────────────────────┼────────┼──────────────────────────────┤ │DISPLAY TIMEOUT INTERVAL │See the │Sets the number of minutes the│ │ │screen │computer waits after the last │ │ │ │key entry to turn off the dis-│ │ │ │play. To restore the display, │ │ │ │To restore the display, press │ │ │ │any key. This does not turn │ │ │ │off the computer. The NEVER │ │ │ │TIMEOUT setting disables the │ │ │ │display timeout function. │ ├─────────────────────────────────┼────────┼──────────────────────────────┤ │LOW POWER BEEPER │ENABLE │Lets you turn on and off the │ │ │DISABLE │Low Power Beeper. │ └─────────────────────────────────┴────────┴──────────────────────────────┘ (/tmc-12/02/95)