Technophone  (170-1066)            Operation           Faxback Doc. # 15109

Press and hold PWR until confirmation tone.

The telephone will carry out a short self-test, briefly displaying a
message (a number or name, as programmed by your dealer).

When the "ON" indicator appears on the display, the telephone is ready for
use.

If the "NO SVC" indicator appears then you are probably outside the
cellular coverage area, and you will not be able to make or receive any
calls.

NOTE:  You can make and receive calls only when the telephone is switched
       on.

MAKING A CALL

Key-in the number (include the area code, even if you are making a local
call); the number will appear on the display.

Press SEND.

The "IN USE" symbol appears on the display, the number clears from the
display, and a tone is heard.

Wait for the call to be answered, then speak.

The elapsed call time is displayed throughout the call (eg, "0115"
indicates 1 minutes and 15 seconds).  Call time gives approximate
indication, and may not reflect actual network usage.

NOTE:  The signal strength, as indicated by the "s" indicator, must be
       adequate;  if it is too low, move to a better position.

If the message "No Service" appears, you are outside the cellular coverage
area.

If the message "Locked" appears, your telephone has been locked.  You can
still make emergency calls, and calls to the number in memory location 38,
when the telephone is locked.

CORRECTING DIALING MISTAKES

Press CLR to clear the last digit, or press and hold CLR to clear the whole
display.

ENDING A CALL

Press END.

RECEIVING A CALL

When there is an incoming call, the ringing tone sounds and the "Call"
message flashes on the display.

If the ringing tone has been switched off (ie, using the "Ring Volume" menu
function) the keyboard and display lights will flash instead, and only a
short beep will be heard.

Press any key except PWR, to answer the call.  The elapsed call time is
displayed throughout the call (eg  "0115" indicates 1 minute and 15
seconds).  (Call timer gives approximate indication, and may not reflect
actual network usage).

If you do not answer the call, the "Call" message will remain on the
display.  Press any key to clear the message.  If the keyboard is locked,
press CLR to clear the message.

NOTE:  The "any key (except PWR) answer" feature is activated immediately
       when an incoming call is received:  should you be using the keyboard
       when an incoming call is received (eg, keying-in a number or
       recalling a memory location), the first keypress after the first
       ring will answer the call.

SETTING THE EARPIECE VOLUME

Press /\ (to increase) or \/ (to decrease).  The level selected is shown by
the volume indicator ("v").

LAST NUMBER REDIAL

Ensure that the display is clear (Press and hold CLR to clear the display)
then press SEND.

The last number you called will appear on the display (even if the
telephone has been switched off since making the call), and the number will
be dialed automatically.

Last number redial is also available using the "Recall Last" menu function.

SWITCHING OFF

Press and hold PWR until confirmation tone, or until display clears.

THE MENU FACILITY

The menu allows you to access any of the menu functions; these are listed
on the next page.

You may access any function, check its current setting (which is displayed
first when the function  is accessed), or change the setting (when
applicable).

The menu functions can be accessed, either, by "scrolling" or by the
"shortcut method".

To access by scrolling:

Press F.  the message "Use <> To View" is displayed.

Press /\ or \/ to reach the function required, then Press STO.

To change the setting (if applicable), press /\ or \/ to display the
setting required, then press STO to select it.

To access by shortcut method:

Press F, then the number of the function required (0 to 8); eg, to select
Call Timers, Press F 3.  The selected function number is shown in the
right-hand corner of the display.

To change the setting (if applicable), press /\ or \/ to display the
setting required, then press STO to select it.

To exit a functions without changing the setting:  Press CLR.

List of Menu Functions

Function          Shortcut        Description

Lock               F 0            Locks/unlocks telephone.

System Select      F 1            Selects roaming option (system feature)

Recall Last        F 2            Recalls last number dialed.

Call Timers        F 3            Displays length of call(s); clears
                                  timers.

Lights             F 4            Sets light to either off, or times (ie,
                                  on for 15 seconds after each keypress)

Key Tones          F 5            Switches keyboard tones on/off.

Ring Volume        F 6            Selects volume of ringing tone.

NAM Select         F 7            Displays and selects cellular number
                                  and network.

Send DTMF          F 8            Sends DTMF tones.


(ALL-05/03/95)