PGL-300  Pager
(170-8001)                 Set-up                     Faxback Doc. # 17650

This section contains instructions for setting the alert tone, selecting
hyphenation, setting the date and time, and setting your pager to stamp
your messages with the date and time they are received.

NOTES:  You must enter each selection within 10 seconds or the pager
        returns to the date/time display.

        See the quick reference card for a visual reference of how to set
        up and use your personal pager.

SETTING THE ALERT TONE

You can select from six different alert tones and two different tone 
durations for the audible mode.

These are the alert tone options you can choose to have sound when your 
pager receives a message:

Loud Beep -- two loud beeps

Soft Beep -- two soft beeps

BELL 1 -- two loud rings

BELL 2 -- two soft rings

BELL 3 -- two very soft rings

NON-STOP VIB -- the pager vibrates until you read the message.

Follow these steps to set the alert tone.

1.  Set ON/OFF to silent or audible. 

2.  Press ON/OFF twice.  ALERT SET appears on the display.

    NOTE:  If there are messages stored in memory, DELETE ALL appears on
           the display.  Press FORWARD to reach the ALERT SET menu.

3.  Press ON/OFF again.  The current alert tone appears on the display.

4.  Press BACKSCROLL or FORWARD until the desired alert tone appears on
    the display.

5.  Press ON/OFF to store your selection.  The current alert tone duration
    mode appears on the display.

    NOTE:  If you choose NON-STOP VIB, you cannot select a duration mode.
           The standby display appears.

6.  If the current duration mode is not the mode you want, press FORWARD
    until the desired duration mode appears on the display.

    Auto Reset -- the alert tone automatically turns off after 8 seconds
    or you can press ON/OFF to turn it off.

    Non-Stop -- the alert tone sounds until you press ON/OFF.

    To test the selected alert tone, set ON/OFF to off (black dot), then
    set it back to silent or audible.

AUTO HYPHEN

You can set the pager to automatically hyphenate the numbers in messages
you receive.  The order of hyphens in your messages depends on your local
paging system.

NOTE:  A message with more than 22 digits will not be hyphenated, even if
       hyphenation is turned on.

Follow these steps to turn on/off auto hyphen.

1.  Set ON/OFF to silent or audible.

2.  Press ON/OFF twice, then FORWARD until AUTO HYPHEN appears on the
    display.

3.  Press ON/OFF.  The current hyphen mode appears on the display.

4.  Press BACKSCROLL or FORWARD to turn auto hyphen on or off.

5.  Press ON/OFF to store your selection in memory.

SETTING THE DATE AND TIME

Setting the Current Date

1.  Set ON/OFF to silent or audible.

2.  Press ON/OFF, FORWARD, ON/OFF, then FORWARD until DAY/DATE SET appears
    on the display.

3.  Press ON/OFF.  DAY SET appears on the display while the current day 
    setting flashes.

4.  Repeatedly press BACKSCROLL or FORWARD until the desired day flashes.

5.  Press ON/OFF.  MONTH SET appears on the display and the month flashes.

6.  Repeatedly press BACKSCROLL or FORWARD until the desired month flashes.

7.  Press ON/OFF.  DATE SET appears on the display and the date flashes.

8.  Repeatedly press BACKSCROLL or FORWARD until the desired date flashes.

9.  Press ON/OFF.  The display returns to the standby mode and the day,
    date, and time appear on the display.

Setting the Current Time

1.  Set ON/OFF to silent or audible.

2.  Press ON/OFF, FORWARD, then ON/OFF until TIME SET appears on the
    display.

3.  Press ON/OFF.  The hour and A (for AM) or P (for PM) flash.

4.  Repeatedly press BACKSCROLL or FORWARD until the correct hour appears
    on the display.

5.  Press ON/OFF.  The minute digits flash.

6.  Repeatedly press BACKSCROLL or FORWARD until the correct minutes appear
    on the display.

7.  Press ON/OFF.  12 or 24 flashes.

8.  Repeatedly press BACKSCROLL or FORWARD until the desired setting
    appears on the display.  Select 12 for the standard AM/PM format or
    select 24 for the 24-hour format.

Turning On The Date/Time Stamp

You can set the pager to stamp your messages with the date and time they
are received.

1.  Set ON/OFF to silent or audible.

2.  Press ON/OFF, FORWARD, ON/OFF, then FORWARD until TIME STAMP appears on
    the display.

3.  Press ON/OFF.  The current stamp mode appears on the display (STAMP ON 
    or STAMP OFF).

4.  Press BACKSCROLL or FORWARD to turn the stamp on/off.

5.  Press ON/OFF to enter your selection into memory.  The display returns 
    to the standby mode.


(CS/all-10/26/95)