ET-293  Two-Line Amplified Trim-Fone
(430-0622)                 Operation                  Faxback Doc. # 19487

RECEIVING A CALL

When you receive a call, that line's green indicator flashes.  To answer a
call, press the line button next to the flashing green indicator and lift
the handset.

PLACING  A CALL

1.  Press the line button for a line that is not in use.

2.  Lift the handset and listen for a dial tone.

3.  Dial the number.

NOTE:  If you are using pulse service, it takes the phone a few seconds to
       finish dialing.

USING RESET

To disconnect a call without hanging up the handset, press RESET and hold
it for about one second.

ADJUSTING THE AMPLIFIED HANDSET'S VOLUME

Roll the amplified handset's volume control up to make the sound you hear
through the handset louder.  Roll it down to make it quieter.

USING REDIAL

Each time you dial a number, the telephone stores that number in a
temporary memory.  If you want to call the last number dialed, lift the
handset and press REDIAL.

NOTE:  If you do not return the handset to the cradle, the phone hangs up
       and then redials automatically after a short time.

The redial memory holds up to 32 digits, so it can store long-distance as
well local numbers.

USING TONE SERVICES ON A PULSE LINE

Some special services, such as bank-by-phone, require tone signals.  If you
have pulse service, you can still use these special tone services by
following these steps:

1.  Be sure TONE/PULSE is set to PULSE.

2.  Call the service.

3.  When the service answers, set TONE/PULSE to TONE.

4.  Follow the normal procedures for the service you are using.  Any
    additional numbers dialed are sent as tone signals.

5.  When you complete the call, set TONE/PULSE back to PULSE and hang up.

To access special services using a pulse line:

1.  Be sure TONE/PULSE is set to PULSE.  Then, dial the number of the
    special service.

2.  When the service answers with a second dial tone, press *.  Any
    additional numbers dialed will now produce tone signals.

    NOTE:  After hanging up, all numbers dialed will be pulse signals
           again.

3.  Follow the special service's dialing procedure.

Using Redial for Tone Services on a Pulse Line

To redial a number that includes a change from PULSE to TONE, leave TONE/
PULSE set to PULSE  and press REDIAL.

The phone stops redialing at the mode change.

Simply press REDIAL a second time to dial the remaining numbers.

PUTTING A CALL ON HOLD

Placing a call on hold lets you hang up the handset or use the other phone
line without disconnecting the first call.

To place a call on hold, press HOLD.  The line's red indicator light comes
on.

To release a call from hold so you can continue the conversation, press
that line's button. You can also release a call from hold by picking up any
extension phone on that line.

MAKING A CONFERENCE CALL

A conference call lets you have a three-way conversation.  To place a
conference call, do the following:

1.  Place a call to one of the parties.

2.  Press HOLD to put the first call on hold.

3.  On the other phone line, place a call to the other party.

4.  After the second party answers, press CONF.  This connects all three
    parties.

NOTE:  During conference calls, long-distance calls might sound weaker than
       local calls.

Using Hold During a Conference Call

To talk on only one line without disconnecting the other line, press HOLD.
Both red indicators come on.  Then, press the button for the line you want
to talk on.

To return to the three-way conversation, press CONF.

Disconnecting One Line During a Conference Call

To disconnect one line and continue talking on the other, press the button
for the line you want to talk on.  This disconnects the other line if it is
not placed on hold.


(EB 1/17/96)