EC-329  (650-0946)             Operation              Faxback Doc. # 16604

CLEARING MEMORY (RESET OPERATION)

1.  Press RESET switch on the back.

    RESET OK? Flashes on the Display


2.  Press SHIFT ENTER.

    (To cancel, press any key other than SHIFT ENTER.)  Data in the
    clock mode such as the time and daily alarm time will also be
    cleared.

DATA TRANSFER

The EC-329 can transfer data (transmit and receive) using the optional
CE-210L data transfer connector.

CE-210L data transfer connector (optional)

      The EC-329 sending data is called the "transmitter" and the EC-329
      receiving data the "receiver".

When connecting two EC-329's:

      The EC-329 on which SHIFT OPTION is first pressed becomes the
      "receiver".

      The EC-329 on which SHIFT OPTION is next pressed becomes the
      "transmitter".

Before transferring data

1.  Press OFF on both the transmitter and receiver to turn off the
    power.

2.  Slide open the connector covers on both the transmitter and receiver.

3.  Properly connect the data transfer connector.

4.  Press "on" C-CE on both transmitter and receiver to turn on the power.

5.  Press MODE on the receiver to select the telephone or schedule mode.

6.  Press SHIFT OPTION on the receiver.  The receiver is in the receive
    mode.

When two EC-329s are connected and one of them is turned off, keys
on the other are inoperative.

Transmission does not alter any data stored in the transmitter.

Press "on" C-CE on the transmitter to stop transferring data.

Transmitted data will be copied to the same file in the receiver (i.e.
Data stored in the transmitter's TEL1 file will be copied to the
receiver's TEL1 file).

Transferring a single listing (single data transfer)

1.  Recall the desired listing on the transmitter.

2.  Press SHIFT OPTION on the transmitter.

    SEND OK? Flashes on the display

3.  Press ENTER on the transmitter.  All data of the recalled listing will
    be transmitted.  After transmission the display returns to the
    previous entry prompt.

Transferring a file listing (file data transfer)

EXAMPLE: Transfer all data in the TEL1 file.

1.  Press MODE on the transmitter to select the TEL1 file.

2.  Press "on" C-CE on the transmitter to display the entry prompt.

3.  Press SHIFT OPTION on the transmitter.

4.  Press 1 on the transmitter to select "TEL" (file data transfer).

To select schedule data transfer, press 2 and proceed step 6.

5.  Press 1, 2 or 3 on the transmitter.
    Pressing 1 selects TEL1 file, 2 the TEL2 file and 3 the TEL3 file.

6.  Press ENTER on the transmitter.
    All data in the file selected in step 5 will be transmitted.

File transfer adds the data to that already in the receiver file.

The EC-329 cannot transfer all of the data in memory at once.

When performing the file data transfer, if the transmitter's Secret
function is on, data in secret listings will not be transmitted.  To
transmit data in secret and non-secret listings, turn off the Secret
function and perform the transmission.  The file data transfer does not
transmit the password.

When transferring data in secret listings, the received secret data will
be treated as non-secret if the password is not registered on the receiver.
If the password is stored, the data becomes secret again.

NOTE:  An I/O error ("IO ERROR!" displayed) can be caused by the following:

       The connector is disconnected or there are abnormal conditions such
       as extraneous noise.

       "ON" C-CE is pressed.

       The batteries are exhausted.

       The receiver memory is full ("FULL! NOT IN" is displayed on the
       receiver.)

Press "on" C-CE to cancel the I/O error.

Pressing "on" C-CE on the transmitter will display the data to be
transmitted next, so that progression of the transmission can be easily
monitored.

    If an alarm time is turned on during data transfer, the alarm will
    sound after the data transfer is completed.

DELETING INFORMATION

1.  Turn unit on.

2.  Press Reset on the back.

3.  Press Shift, then Enter.


ENABLING/DISABLING KEY-TONES

Press the music note symbol in the Calculator mode to turn the key-tone on
and off.  When key-tone is on, the music note symbol appears in the
calculator mode.


(br/ir-03/28/96)