LCD Jumbo Display Dual Timer/Clock
(630-0898)                 Operation                  Faxback Doc. # 18083

SETTING THE CLOCK

1.  Repeatedly press MODE until CLOCK appears in the upper left corner
    of the display.

      NOTE:  Repeatedly press CLEAR to change between the 12- and 24-hour
             formats.  PM appears on the display to indicate a PM hour
             when the clock is in the 12-hour format.

2.  Repeatedly press (or press and hold down) HOUR until the correct
    hour appears.

3.  Repeatedly press (or press and hold down) MINUTE until the correct
    minute appears.

      NOTE:  When you press and hold down MINUTE or SECOND, the setting
             advances in increments of 10.

4.  Repeatedly press (or press and hold down) SECOND until the correct
    second appears.

COUNTING UP 

The two timers can count up to 29 hours, 59 minutes, and 59 seconds.  Then
they reset and begin counting from 0:00 00 again.  You can use either
timer, or both at the same time.

1.   While CLOCK appears on the display, press MODE.  COUNT UP1, COUNT UP2,
     and their timers appears on the display.

     NOTE:  If either or both timers do not show 0:00 00, press CLEAR to
            reset them.

2.    Press TIMER 1 or 2 to start COUNT UP1 or COUNT UP2.

      NOTE:  You can start COUNT UP1 and COUNT UP2 to have both counters
             running at the same time.

3.    Press TIMER 1 or 2 to stop COUNT UP1 or COUNT UP2.

      NOTE:  You can press TIMER 1 or 2 again to continue counting up.

4.    Press CLEAR to reset both timers to 0:00 00.

COUNTING DOWN

You can use the two countdown timers for activities that require a
predetermined amount of time, such as baking a cake or playing a
basketball game.  The timers count down in 1-second increments.

NOTE:  The maximum countdown time is 29 hours, 59 minutes, and 59 seconds.

1.  While CLOCK appears on the display, press MODE twice for TIMER 1
    and 0:00 00 to appear on the display.

    NOTE:  Press MODE three times for TIMER 2 to appear on the display,
           or press MODE four times for both timers to appear on the
           display.

2.  Repeatedly press (or press and hold down) HOUR until the desired
    hour appears.

3.  Repeatedly press (or press and hold down) MINUTE until the desired
    minute appears.

    NOTE:  When you press and hold down MINUTE or SECOND, the setting
           advances in increments of 10.

4.  Repeatedly press (or press and hold down) SECOND until the desired
    second appears.

5.  Press TIMER 1 OR TIMER 2 to start counting down.

NOTES:  You can start TIMER 1 and then start TIMER 2 (or vice versa) to
        use them both at the same time.

        To pause the countdown before the timer reaches 0:00 00, press
        TIMER 1 or TIMER 2.  To resume the countdown, press the same
        button again.

        To stop the countdown before the timer reaches 0:00 00, press
        TIMER 1 or TIMER 2 , then press CLEAR.  The timer resets to 0:00
        00.

When the timer reaches 0:00 00, the alarm sounds for 1 minute and TIMES UP
flashes above the active timer.  Then the timer counts up in 1-second
intervals.  Press any button to silence the alarm.

When the alarm stops sounding, TIMES UP continues to flash on the display
and the timer continues to count up.  To stop the countup, press the
active timer's button.  The timer resets to 0:00 00.

USING THE CLOCK AND TIMERS

You can view the clock and use the timers at the same time.  After you set
the countup or countdown timers, press MODE until CLOCK and the time
appear in the upper left corner of the display.

The active timer(s) flash on the display (e,g., if you are using TIMER 1's
countup timer, TIMER 1 flashes on the clock's display).

Repeatedly press MODE to switch between viewing the clock and the countup
and countdown timers.

MOUNTING THE TIMER/CLOCK

The magnet on the back of the timer/clock holds it on any metal surface,
such as a refrigerator, oven, or file cabinet.

You can also clip the timer/clock to a clipboard or your shirt pocket. 
Press and hold down the upper end of the clip, attach it to your shirt or
clipboard, and release the clip.

USING THE STAND

1.  Press and hold down the upper end of the clip.

2.  Use a pencil tip to pull the small metal stand out until it fits
    onto the clip.

3.  Set the timer on a table or desk.


(PH 11/14/95)