Flip-Top Calculator Chronograph Alarm Watch
(630-5085)                 Operation                  Faxback Doc. # 18527

SETTING THE ANALOG DISPLAY

1.  Lift up on the tab below the clock's face to open it, then pull out the
    stem.  The second hand stops.

2.  Turn the stem to adjust the time.

3.  Push the stem back in after setting the time.  The second hand starts
    again.

A LOOK AT THE KEYS

To use the digital watch and calculator, lift up on the tab below the
analog watch face to open it.

The digital watch face has four operating zones/keys that you use to
operate the watch.

S1 - Includes 0, 1, 2, 4, 5, and ..  Press one of these keys on the 
     keypad when this manual refers to S1.

S2 - Includes +/=, 3, 6, -, x and divide.  Press one of these keys on 
     the keypad when this manual refers to S2.

 7 - press as required by each procedure.

 C - press as required by each procedure.

 You use all of the keys to operate the calculator.

OPERATING MODES

The digital watch has five operating modes:

    Clock  -  displays hours, minutes, seconds and day of the week.

    Calendar - displays month, date and day of the week.

    Alarm - lets you set and display the alarm time on hours and minutes.

    NOTES:  To hear what the alarm sounds like, at the clock display, press
            and hold S1, then press S2.  The alarm sounds until you release
            one of the keys.

    Stopwatch (Chronograph) - lets you time an event from start to finish 
                              and track laps with split times.

    Calculator -     lets you perform basic arithmetic calculations
                     and displays the results.

    NOTES:  When you are in the calculator or alarm mode or when you are
            setting the time or alarm time, the watch automatically returns
            to the clock display if you do not press a key for 2-3 minutes.

SETTING THE TIME (DIGITAL DISPLAY)

1.  From the clock display, press and hold C for 3-4 seconds.  The alarm
    setting display appears.

2.  Press C again.  The clock-setting display appears, and the seconds
    digits flash.

3.  Press S1 to reset the seconds to 00.

    NOTE:  If the seconds were 30 or greater, the minutes advance by one.

4.  Press S2 to select the setting you want to change.  The selected
    digits flash.

    NOTE:  The setting sequence is seconds, hours, minutes, month, date
           and weekday.

5.  Press (or press and hold) S1 to advance the flashing digit.

    NOTE:  While on the hour setting, press 7 to change between the AM/PM
           and 24-hour formats.  In the AM/PM format, AM or PM appears on
           the display above the hour.

6.  Press C to return to the clock display.

    NOTE:  Press S2 to alternate between the clock and the calendar.

SETTING THE ALARM TIME

1.  From the clock display, press and hold C for 3-4 seconds.  The alarm-
    setting display appears with the alarm hour flashing.

2.  Press (or press and hold) S1 to advance the hour.

    NOTE:  In the AM/PM format, AM appears during AM hours and PM appears
           during PM hours.

3.  Press S2 to select the alarm minutes.  The minutes flash.

4.  Press (or press and hold) S1 to advance the minutes.

5.  Press C twice to return to the clock display.

    NOTE:  Press S1 to alternate between the clock display and the preset
           alarm time.

TURNING THE ALARM CHIME ON/OFF

1.  From the clock display, press S1 to change to the alarm mode.  The
    display shows the alarm time and AL.

2.  Press S2 until the desired display appears.

    Sound - alarm is on.  When the alarm is on, the watch sounds for 20
            seconds at the set alarm time each day.  Press any key to 
            silence the alarm sooner.

    Bell -  chime is on.  When the chime is on, the watch chimes at the
            beginning of each hour and beeps each time a key is pressed 
            when you use the calculator.

    Bell Sound - chime and alarm are both on.

3.  Press S1 to return to the clock display.

USING THE STOPWATCH

The stopwatch tracks the elapsed time in hundredths of seconds up to one 
hour.  After one hour, it tracks the time in hours, minutes, and seconds up 
to 11 hours 59 minutes and 59 seconds.  Then the watch returns to 00-00.

1.  From the clock display, press 7 once.  00-00 00 and CH appears.

2.  Press S2 to start the stopwatch.

3.  To measure split time, press S1 while the stopwatch is running.

    SP flashes and the display stops, but the stopwatch continues to run. 
    After you record the split time, press S1 to return to the running
    time.

    NOTE:  Split time is the total elapsed time measured from the
           stopwatch start time.

4.  Press S2 again to stop the stopwatch.

5.  Press S1 to reset the stopwatch.

6.  Press 7 to return to the clock display.

USING THE CALCULATOR

The calculator performs four basic operations (+, -, x, divide) with
8-digit accuracy.

1.  From the clock display, press C.

2.  Press the number and symbol keys on the keypad to perform calculations.

3.  Press C to clear the display.

    NOTES:  * - appears in the top left if the calculation result is
            negative.

            * E (error) appears in the top right if a calculation result
            exceeds eight digits or if you divide by zero.  Press C to
            clear the error.

            * When the chime is on, the watch beeps each time you press a
            key when you use the calculator.

4.  Press C again to return to the clock display.


(JC   11/7/95)