Wireless Home Security System (490-2551) Installation Faxback Doc. # 19531 This section describes how to initialize all of the system's accessories so they are recognized by the console and how to test the system to make sure it is working properly. Perform all the procedures in this section, and then follow the instructions in "Locating and Mounting Accessories." You can add other separately purchased accessories to the system by following the appropriate initialization and testing procedures in this section. SETTING UP THE CONSOLE 1. Choose a location for the console that is: Close to a telephone jack so you can easily connect the telephone dialer. Central to the doors/windows you want to protect so all sensors are within range of the console (100 feet). Positioned where you can easily check the zone indicators for any problems, but not where an intruder could easily see it. 2. Set the house and unit code dials on the console to A1. NOTE: You can set the console to any house code, but you must also set all accessories/sensors to the same house code. 3. Place the telescoping antenna in an upright position and fully extend it. 4. For backup power in case of an AC power failure, place a 9-volt alkaline battery (Cat. No. 23-553) in the battery compartment. See "Replacing the Console's Battery." NOTE: Be sure to install the backup battery. If there is no battery and the console loses AC power, you must re-initialize all of the system's accessories. 5. Plug the console into any standard AC outlet that is not controlled by an on/off switch. 6. Plug the telephone cord into the console and plug the other end into a modular phone jack. NOTES: If you do not have an unused jack, use the supplied duplex adapter. For a baseboard jack, plug the adapter into the jack; for a wall jack, plug the adapter into the console. If you do not have a modular phone jack, you can either update the wiring yourself or have the phone company do it for you. Radio Shack stores sell the jacks and adapters you need. The USOC number of the jack to be installed is RJ11C for a baseboard jack or RJ11W for a wall jack. INSTALLING THE KEYCHAIN REMOTE CONTROL 1. Slide off the keychain remote control's battery compartment cover. Install two AAA alkaline batteries (Cat. No. 23-555) in the compartment, according to the polarity symbols (+ and -) marked inside. Then replace the compartment's cover. 2. Set the console's INSTALL/RUN 1/RUN 2 switch to INSTALL. 3. Stand near the console and press ARM on the remote control. The console chimes once and the LED on the remote control blinks twice. 4. Press ARM again. The LED blinks again, and the console chimes and logs in the remote control. 5. Leave the console's switch set to INSTALL to install other accessories. NOTES: You can add any combination of up to eight Plug'n Power remote control. When you press a button, the BATTERY indicator on the remote control lights to show the battery is good. INSTALLING THE HANDHELD REMOTE CONTROL 1. Press the tab on the battery compartment cover and lift off the cover. 2. Install four AAA alkaline batteries (Cat. No. 23-555) in the handheld remote control's battery compartment, according to the polarity symbols (+ and -) marked inside the compartment. 3. Be sure the console's INSTALL/RUN 1/RUN 2 switch is set to INSTALL. 4. Set the house code on the remote control to the same letter as the console. 5. Press ARM HOME or ARM AWAY on the handheld remote control. The console chimes. NOTE: If you do not hear a chime, press the button beneath the remote control's label with a pencil. Then repeat this step. 6. Leave the console's switch set to INSTALL to install other accessories. 7. Replace the battery compartment cover. NOTE: You can add any combination of Plug'n Power keychains (Cat. No. 49-2591) or heldheld remote controls (Cat. No. 49-2551T), up to a total of eight. INITIALIZING THE WIRELESS SENSOR TRANSMITTERS 1. Lift open a wireless sensor transmitter's battery compartment cover. Press and hold down TEST, located to the right of the compartment, long enough to fully discharge the sensor (about 3 seconds). Install two AA alkaline batteries (Radio Shack Cat. No. 23-557) in the compartment. 2. Be sure the console's INSTALL/RUN 1/RUN 2 switch is set to INSTALL. 3. Press TEST for about 1 second and release. The LED blinks twice to generate a new code. NOTE: The LED flashes rapidly during a violation or after TEST is pressed. When the batteries' voltage drops below around 2.7V, the LED flashes twice when TEST is pressed to indicate that the batteries are weak. 4. Stand near the console and press TEST. The wireless sensor transmitter's LED blinks. 5. Release TEST. The console chimes and logs in the newly generated code for the wireless sensor transmitter. The first available zone indicator on the console lights. 6. Set DELAY, located inside the wireless sensor transmitter's battery compartment, to MIN to protect a window or to MAX to protect a door. Then close the battery compartment's cover. 7. Place one of the supplied numbered stickers on the sensor to show its zone number. 8. Leave the console's switch set to INSTALL to install other accessories. Repeat Steps 1-8 for additional wireless sensor transmitters. INITIALIZING THE MOTION DETECTOR 1. Press the four dots on the battery compartment cover and slide the cover down to remove it. 2. Install four 1.5V AA alkaline batteries (Cat. No. 23-552) inside the motion detector's battery compartment according to the polarity symbols (+ and -) and replace the cover. 3. Be sure the console's INSTALL/RUN 1/RUN 2 switch is set to INSTALL. 4. Press TEST on the back of the motion detector. The console chimes, and the first available zone indicator lights to show the console has logged in the motion detector. If you do not hear a chime, press CODE with a pencil, then press TEST again. 5. Looking at the back of the motion detector, set the switch on the left side to 1. 6. Place one of the supplied numbered stickers on the motion detector to show its zone number. 7. Leave the console's switch set to INSTALL to install other accessories. 8. Replace the battery compartment cover. INSTALLING THE LAMP MODULE When the alarm trips, lamps connected to lamp modules flash on and off for the duration of the alarm. After 4 minutes (or when you disarm the alarm), the lamps stop flashing and remain on. If you arm the system with an exit delay, lamp modules that are set to the same House and Unit code as the console turn on during the exit countdown time. You can also control lamp modules set to this code from LIGHT ON and LIGHT OFF on the keychain remote control, or using SECURITY LIGHT on the handheld remote. Follow these steps to install a lamp module. 1. Plug a lamp into the supplied lamp module and plug the module into an AC outlet that is on the same electrical circuit as the console. Be sure the lamp's on/off switch is on. 2. Set the lamp module's House and Unit code dials to the same letter as the console and the same number (1,2,3, or 4) as the button that will control it. TESTING THE SYSTEM After you have completed all of the quick installation procedures, follow these steps to test the system. NOTE: To avoid unnecessarily alarming your neighbors, tell them you are testing the system. 1. Set the INSTALL/RUN 1/RUN 2 switch on the console to RUN 2. The REC/ BUSY light stays on for 15 seconds. 2. Place each wireless sensor transmitter's magnet next to its magnetic switch with the arrows pointing toward each other. 3. Place the motion detector on a counter top within 100 feet of the console. 4. Move a wireless sensor transmitter's magnet away from the magnetic switch. When the system is not armed, the console emits a chime every time someone opens a door or window with the system disarmed in the RUN 2 mode. The system does not chime in the RUN 1 mode. Replace the magnet next to the magnetic switch. 5. Press ARM on a remote control, and then move the magnet away from the magnetic switch again. The alarm sounds and the lamp connected in the lamp module flashes on and off. Press DISARM to turn off the alarm, and LIGHTS OFF to turn off the lamp. Replace the magnet next to the magnetic switch. 6. Press ARM AWAY on the remote control, then walk across the path of the motion detector's lens. The alarm sounds and the lamp connected to the lamp module flashes on and off. Press DISARM to turn off the alarm. The console chimes twice. Press LIGHTS OFF to turn off the lamp. (JC 1/22/96)