CENTRAL 5000 Monitored Wireless Security Alarm System (490-2570) Installation Faxback Doc. # 32976 QUICK INSTALLING/TESTING YOUR SYSTEM This section describes how to initialize system accessories so the console recognizes them and how to test the system to make sure it works properly. Perform all the procedures in this section, then follow the instructions in "Locating and Monitoring Accessories", on Faxback Doc. # 32977. You can add separately purchased accessories to the system by following the appropriate initialization and testing procedures in this section. SETTING UP THE CONSOLE 1. Choose a location for the console that is: Close to a modular phone jack. Central to doors/windows you want to protect so all sensor transmitters are within 100 feet. Positioned where you can easily check the zone indicators for problems, but not where an intruder could easily see it. 2. For backup power in case of an AC power failure, connect and place a 9-volt alkaline battery (Cat. No. 23-553) in the battery compartment. 3. Plug the console into any standard AC outlet that is not controlled by an on/off switch, then fully extend the antenna. 4. Plug the telephone cord into the console and plug the other end into a modular phone jack. NOTES: If you do not have an unused jack, use the supplied duplex adapter. For a baseboard jack, plug the adapter into the jack; for a wall jack, plug the adapter into the console. If you do not have a modular phone jack, you can either update the wiring yourself or have the phone company do it for you. Radio Shack stores sell the jacks and adapters you need. The phone company charges to install the jacks. The USOC number of the jack to be installed is RJ11C for a baseboard jack or RJ11W for a wall jack. INSTALLING THE KEYCHAIN REMOTE CONTROL 1. Remove the keychain remote control's back cover. Install two AAA alkaline batteries (Cat. No. No. 23-555) in the battery compartment, according to the polarity symbols (+ and -) marked inside. Then replace the cover. 2. Set the console's INSTALL/RUN 1/RUN 2 switch to INSTALL. 3. Stand near the console and press ARM on the remote control. The console chimes and logs in the remote control. 4. Leave the console's switch set to INSTALL to install other accessories. NOTES: You can add any combination of up to eight Plug 'n Power remote controls. When you press a button, the BATTERY indicator on the remote control lights to show the battery is good. INSTALLING THE HANDHELD REMOTE CONTROL 1. Press the tab on the battery compartment cover and lift off the cover. 2. Install four AAA alkaline batteries (Cat. No. 23-555) in the handheld remote control's battery compartment, according to the polarity symbols (+ and -) marked inside the compartment. 3. Be sure the console's INSTALL/RUN 1/RUN 2 switch is set to INSTALL. 4. Set the house code on the remote control to the same letter as you selected when you set up service. 5. Press ARM HOME or ARM AWAY on the handheld remote control. The console sounds a tone. NOTE: If you do not hear a tone, press the button beneath the remote control's label with a pencil. Then repeat this step. 6. Leave the console's switch set to INSTALL to install other accessories. 7. Replace the compartment cover. NOTE: You can install eight keychain (Cat. No. 49-2591) or handheld remote controls (Cat. No. 49-2551T). INITIALIZING THE DOOR/WINDOW SENSOR TRANSMITTERS 1. Open a door/window sensor transmitter's battery compartment. Install two AA alkaline batteries (Radio Shack Cat. No. 23-557). 2. Be sure the console's INSTALL/RUN 1/RUN 2 switch is set to INSTALL. 3. Stand near the console and press TEST, located to the right of the sensor transmitter's battery compartment. The console chimes and logs in the door/window sensor transmitter. The first available zone indicator on the console lights to show which zone the sensor transmitter is assigned to. NOTE: If you do not hear a chime, remove the batteries from the sensor transmitter and then hold down the TEST button for 3 seconds. Reinstall the batteries and press TEST again. When the indicator flashes twice, you can initialize the sensor transmitter as described in Step 3. 4. Set DELAY, located inside the door/window sensor transmitter's battery compartment, to MIN to protect a window or to MAX to protect a door. Then replace the battery compartment's cover. 5. Place one of the supplied numbered stickers on the sensor transmitter to show its zone number. 6. Leave the console's switch set to INSTALL to install other accessories. Repeat these steps for additional door/window sensor transmitters. INITIALIZING THE MOTION DETECTOR 1. Press the four dots on the battery compartment cover and slide the cover down to remove it. 2. Install four 1.5V AA alkaline batteries (Cat. No. 23-552) inside the motion detector's battery compartment according to the polarity symbols (+ and -) marked inside. 3. Be sure the console's INSTALL RUN 1/RUN 2 switch is set to INSTALL. 4. Press TEST on the back of the motion detector. The console chimes, and the first available zone indicator lights to show the console has logged in the motion detector. If you do not hear a chime, press CODE with a pencil, then press TEST again. 5. Looking at the back of the motion detector, set the switch on the left side to 1 (see "Mounting the Motion Detector" on Faxback Doc. # 32977). 6. Place one of the supplied numbered stickers on the motion detector to show its zone number. 7. Leave the console's switch set to INSTALL to install other accessories. 8. Replace the motion detector's battery compartment cover. INSTALLING THE LAMP MODULE When the alarm trips, lamps connected to lamp modules flash on and off for the duration of the alarm. After 4 minutes (or when you disarm the alarm), the lamps stop flashing and remain on. If you arm the system with an exit delay, lamp modules set to the same House and Unit Code as the console turn on during the exit countdown. You can also control lamp modules set to this code using SECURITY LIGHT on the handheld remote. Follow these steps to install a lamp module. 1. Plug a lamp into the supplied lamp module and plug the module into an AC outlet that is on the same electrical circuit as the console. NOTE: Do not plug an appliance or fluorescent lamp into the supplied module. 2. Be sure the lamp's switch is on. 3. Set the module's House and Unit Code dials to the same codes you selected when you set up service. TESTING THE SYSTEM After you complete the quick installation procedures, follow these steps to test the system. NOTE: To avoid alarming neighbors, tell them you are testing the system. 1. Set INSTALL/RUN 1/RUN 2 on the console to RUN 2. 2. Place each door/window sensor transmitter's magnet next to its magnetic switch. 3. Place the motion detector on a counter top within 100 feet of the console. 4. Move a door/window sensor transmitter's magnet away from the magnetic switch. When the system is not armed, the console chimes every time someone opens a door or window with the system in the RUN 2 mode. The system does not chime in the RUN 1 mode. Replace the magnet next to the magnetic switch. 5. Press ARM on a remote control, and then move the magnet away from the magnetic switch again. The alarm sounds and the lamp connected to the lamp module flashes on and off. Press DISARM to turn off the alarm, and LIGHTS OFF to turn off the lamp. Replace the magnet next to the magnetic switch. 6. Press ARM on the remote control, then walk across the path of the motion detector's lens. The alarm sounds and the lamp connected to the lamp module flashes on and off. Press DISARM to turn off the alarm. The console chimes twice. Press LIGHTS OFF to turn off the lamp. (LB/EB 5/8/96)