8-Zone Alarm System  (490-0485)  System Indicators      Faxback Doc. # 8829

The system has several indicators.  Refer to the following table to
understand each indicator's meaning.

┌──────────────┬─────────────────────┬───────────────────┬────────────────┐
│INDICATOR     │ON                   │OFF                │     FLASHING   │
├──────────────┼─────────────────────┼───────────────────┼────────────────┤
│DELAY         │Testing the system   │System is not      │System is in    │
│              │or setting the delay │armed.             │entry or exit   │
│              │times.               │                   │delay.          │
├──────────────┼─────────────────────┼───────────────────┼────────────────┤
│AWAY          │System armed in      │System not armed   │----------------│
│              │away mode.           │in away mode.      │                │
├──────────────┼─────────────────────┼───────────────────┼────────────────┤
│HOME          │System armed in      │System not armed   │----------------│
│              │home mode.           │in home mode.      │                │
├──────────────┼─────────────────────┼───────────────────┼────────────────┤
│FIRE          │Smoke or fire has    │Fire zone OK.      │Trouble with    │
│              │been detected.       │                   │fire zone wiring│
├──────────────┼─────────────────────┼───────────────────┼────────────────┤
│1,2,3,4,      │Zone OK and protected│Zone not protected │Sensor in zone  │
│5,6, or 7     │when armed.          │when armed.        │is/has been     │
│              │                     │                   │violated or     │
│              │                     │                   │entry/exit delay│
│              │                     │                   │activated.      │
├──────────────┼─────────────────────┼───────────────────┼────────────────┤
│8             │-------------------- │Panic zone OK.     │Panic zone      │
│              │                     │                   │violated.  Or if│
│              │                     │                   │FIRE also flash-│
│              │                     │                   │ing, fire zone  │
│              │                     │                   │problem.        │
├──────────────┼─────────────────────┼───────────────────┼────────────────┤
│ARMED         │System Armed         │System not armed.  │Alarm has sound-│
│              │                     │                   │ed since last   │
│              │                     │                   │alarm.          │
├──────────────┼─────────────────────┼───────────────────┼────────────────┤
│BATTERY       │AC disconnected-     │AC connected or    │Battery disconn-│
│              │operating from       │no power connected.│ected or dead or│
│              │battery              │                   │BATTERY fuse has│
│              │                     │                   │blown.          │
├──────────────┼─────────────────────┼───────────────────┼────────────────┤
│STATUS        │All zones OK.        │------------------ │A zone's sensor │
│              │                     │                   │is violated.    │
└──────────────┴─────────────────────┴───────────────────┴────────────────┘

TESTING THE SECURITY SYSTEM

Follow these steps to test the system when you complete installation and
once per week, thereafter.

1.  Disarm the system.

2.  Be sure the BATTERY indicator is off.

3.  Remove the screw that secures the power adapter to the AC outlet, and
    unplug the adapter.

                                      OR

    Turn off the breaker (or remove the fuse) that controls power to the
    AC outlet you have plugged the power adapter into.

4.  Be sure the BATTERY indicator is on.

    If it is not on, check the connections to the backup battery and check
    the BATTERY fuse.  If all connections are secure and the fuse is good,
    replace the batteries.  Otherwise, correct the problem before you
    continue.

5.  Press DELAY.  The DELAY indicator lights.

6.  Violate each sensor in every zone except the panic zone, one at a
    time.  If the sensor is functioning properly, each time you violate a
    sensor, the sensor's zone indicator flashes and the console sounds a
    tone.

7.  If any sensor is not functioning properly, repair or replace the
    sensor for full protection.

BEFORE YOU PERFORM THE NEXT TESTS, NOTIFY NEIGHBORS AND THE PROPER
AUTHORITIES.  THESE TESTS WILL MAKE THE SYSTEM'S ALARM SOUND.

8.  If you have install LED a security dialer, disconnect it from the
    system.

9.  Press each panic switch.

The burglar alarm sounds.  Disarm the system to silence the alarm.

10. Reconnect the security dialer.

11. Press and hold down DELAY.  After about 2 seconds, the burglar alarm
    sounds for 1 second.  Then, the fire alarm sounds for 1 second.  The
    system alternates between the two alarms while you hold down DELAY.

12.  If either alarm does not sound, check the wiring and fuses for the
     alarms.  (BURGLAR fuse for the burglar alarm and FIRE fuse for the
     fire alarm).  Correct the problem.

13. After you complete all tests, reconnect the power adapter.

14. Press DELAY so that the DELAY indicator is off to return to normal
    operation.

(SMC/jlc-02/22/94)